24 gallon electric bain marie

Steam powered cooking and distillation devices.

Moderator: Site Moderator

Post Reply
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

24 gallon electric bain marie

Post by shadylane »

I traded for this recently, I think it's made for melting candle wax and soap.
I'm not sure what to do with it.
For now I'll use it for a mash cooker and a heated fermenter.
The thermostat controlled heater is 115v 1500w that's probably too big for heating a fermenter.
Figure to use a controller to turn the power down.
In the future, I might make a water sealed lid and use it for distilling on the grain or pulp.
Attachments
DSCF0001 (375x500).jpg
DSCF0002 (375x500).jpg
User avatar
FreeMountainHermit
Site Donor
Site Donor
Posts: 1769
Joined: Thu May 12, 2011 6:45 pm
Location: Two Dogs Holler, West Virginia

Re: 24 gallon electric bain marie

Post by FreeMountainHermit »

shadylane wrote: The thermostat controlled heater is 115v 1500w that's probably too big for heating a fermenter.
Figure to use a controller to turn the power down.
Given your mad scientist skills I would think that a warm water circulator would be just the ticket to maintain ferments at the desired temperature.

I assume the vessel has fill and drain ports ?
Blah, blah, blah,........
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

That's freaking awesome. Can't wait to see the water sealed lid.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
ben stiller
Site Donor
Site Donor
Posts: 616
Joined: Mon Nov 17, 2014 5:49 pm
Location: New York

Re: 24 gallon electric bain marie

Post by ben stiller »

Best to just send that this way :ebiggrin: . Seriously that is an awesome score no matter what you decide to do with it.
User avatar
bearriver
Site Donor
Site Donor
Posts: 4442
Joined: Fri Nov 22, 2013 10:17 pm
Location: Western Washington

Re: 24 gallon electric bain marie

Post by bearriver »

Ive never seen a vessel that thick.

Nice find!
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

bearriver wrote:Ive never seen a vessel that thick.

Nice find!
It's not that thick, it has a water jacket
Attachments
bain marie.png
bain marie.png (13.89 KiB) Viewed 12522 times
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Spent the morning cleaning old wax off the dadburn thing. Figured it was time to quit cleaning, and start playing with it.
Beyond a doubt, the 1500w heater would be useless for distilling. It's made for melting wax and holding it around 140f.
The pot is 24 gallons and the water jacket holds another 8, with 32 gallons total, saying the 1500w heater is slow and gentle is an understatement.
I'll probably bypass the mechanical thermostat and control the heater with a stc-1000 and a solid-state relay.
Figure it should make a great temp controlled fermenter for this winter :thumbup:
RedwoodHillBilly

Re: 24 gallon electric bain marie

Post by RedwoodHillBilly »

With a PID controller, it would make a nice mash tun also. If you wanted to, you could easily do a step mash with that rig.
User avatar
Brutal
Site Donor
Site Donor
Posts: 1349
Joined: Sat May 18, 2013 6:02 pm

Re: 24 gallon electric bain marie

Post by Brutal »

Fit a medium density 5500 watt element to the element fitting and put glycerin or oil in the jacket. Then seal the lid somehow.

I was going to do a water seal in my new project but decided against it. Loved the idea but you need something on the inside to keep it from constantly filling the water trough with liquid condensing on the inside.
Steam injection rig http://tinyurl.com/kxmz8hy
All grain corn mash with steam injection and enzymes http://tinyurl.com/mp6zdt5
Inner tube condenser http://tinyurl.com/zkp3ps6
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

I'm using water in the bain marie for mashing and fermenting.
When I use it for distilling, I'll need something with a higher boiling point than water.
There's a 18 gallon mash, made from corn and oats fermenting in it at the moment.
A side benefit of the water jacket is, it makes a good wort chiller also. :thumbup:
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Brutal wrote:I was going to do a water seal in my new project but decided against it. Loved the idea but you need something on the inside to keep it from constantly filling the water trough with liquid condensing on the inside.
Something I've noticed, all the water seals I've seen on youtube have the inner lip 2 to 3 inches lower than the outer lip.
Figure the water seals are made that way so instead of overfilling they drain back into the pot.
If they were compensating for boiler pressure, the inner lip would only need to be a 1/2" shorter
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

I don't understand.

Brutal, do you mean the water seal overfills and overflows all by itself? More than you would expect from heat expansion? I have to leave my water bath about an inch low at the start to keep it from overflowing when it gets up to temp.

Shady, here are some pics from Al-Ambiq. It looks like their inner lip is higher than the outer. I thought the lid sat on the inner lip. Note the overflow tube at 4 o'clock.
90-1762-thickbox.png
90-1759-thickbox.png
EDIT spelling.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

I tried using oil in the water jacket. I found it was a good idea to keep a thermometer in it to keep the oil well below the smoking point. It gets pretty nasty when it gets too hot. I've never tried glycol.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
rad14701
retired
Posts: 20865
Joined: Wed Dec 19, 2007 4:46 pm
Location: New York, USA

Re: 24 gallon electric bain marie

Post by rad14701 »

The inner lip being lower is done so that if there is parasitic reflux the alcohol laden water will overflow into the boiler rather than down the outside where it could ignite or quench open flame heat beneath...
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

That would make sense. The height of the inner lip would establish the maximum depth of the seal and anything more would have to run down inside.

Brutal, does it work like that? or did you do it differently?

The seal would have to be deep enough to overcome the boiler pressure, but with a potstill that shouldn't be more than around 1/2 inch, IIRC.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

Here is what Al-Ambiq says. http://www.copper-alembic.com/ns/catego ... category=9

Code: Select all

 What is unique about this still is that it uses water to seal off vapours from the interior, thus having no need to use any other sealing technique as in other models. The pot is built with two separate walls on the top side creating a chamber or corridor where the water is placed.
The inner wall is higher than the exterior one, and this is one of the essential elements of the water sealing system, as this wall must touch the lid to aid in sealing off all vapours. The complete system, independent of its size must be mounted on a perfectly level surface to avoid water spilling from the water corridor when in use.
It sounds like they are more concerned with the lid resting on the inner lip than about its height.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
rad14701
retired
Posts: 20865
Joined: Wed Dec 19, 2007 4:46 pm
Location: New York, USA

Re: 24 gallon electric bain marie

Post by rad14701 »

skow69 wrote:Here is what Al-Ambiq says. http://www.copper-alembic.com/ns/catego ... category=9

Code: Select all

 What is unique about this still is that it uses water to seal off vapours from the interior, thus having no need to use any other sealing technique as in other models. The pot is built with two separate walls on the top side creating a chamber or corridor where the water is placed.
The inner wall is higher than the exterior one, and this is one of the essential elements of the water sealing system, as this wall must touch the lid to aid in sealing off all vapours. The complete system, independent of its size must be mounted on a perfectly level surface to avoid water spilling from the water corridor when in use.
It sounds like they are more concerned with the lid resting on the inner lip than about its height.
That says the opposite... Perhaps they rely on evaporation...
User avatar
Brutal
Site Donor
Site Donor
Posts: 1349
Joined: Sat May 18, 2013 6:02 pm

Re: 24 gallon electric bain marie

Post by Brutal »

Skow, I did not actually go with a water seal. In my case I'm fitting a SS bowl shaped lid to a SS container. As vapor condenses on the inside of the bowl it will run down the sides and into where my water seal would have been. I just didn't have room for that, but I hope to build something with a water seal one day.
Steam injection rig http://tinyurl.com/kxmz8hy
All grain corn mash with steam injection and enzymes http://tinyurl.com/mp6zdt5
Inner tube condenser http://tinyurl.com/zkp3ps6
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Guess I should have started this post in the boiler section :lol:
Here's how I'll make a water seal for the bain marie.
Two strips of SS will be welded around the top for the seal and a copper lid will be made.
Attachments
bain marie water seal.png
bain marie water seal.png (4.93 KiB) Viewed 12269 times
User avatar
skow69
Site Donor
Site Donor
Posts: 3230
Joined: Tue Dec 06, 2011 3:03 am
Location: Cascadia

Re: 24 gallon electric bain marie

Post by skow69 »

Yes. I think the question, at this point, is what supports the weight of the lid? Because that will heavily influence which lip is higher and therefor the fundamental design of the seal.
Distilling at 110f and 75 torr.
I'm not an absinthe snob, I'm The Absinthe Nazi. "NO ABSINTHE FOR YOU!"
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

shadylane wrote:I'm using water in the bain marie for mashing and fermenting.
When I use it for distilling, I'll need something with a higher boiling point than water.
There's a 18 gallon mash, made from corn and oats fermenting in it at the moment.
A side benefit of the water jacket is, it makes a good wort chiller also. :thumbup:
The key is to only have enough water to safely cover the element. For this method you must have some remaining head space within the jacket that will allow for vapor. It is the vapor that gives the heating capability at distilling temps. Not the actual boiling water.

1500 watt element would have no problem making enough vapor (steam) for a kettle that size. 1 bar will give you 250 degrees F.

You will have way more control if using water than you will have with oil. You will need a PRV no matter what heating medium you use.

Maybe not worth it to mod your vessel but seems like it would be no problem to replace that existing fill port with a ferrule so that you could pressurize the vessel.
Attachments
Hobby Baine Marie.png
Trample the injured and hurdle the dead.
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

Ah,, just saw where you said a thermostatic controlled element. Obviously that would have to go. But 1500 watts would work nicely under 1 bar with that small amount of heating medium to bring to temp.
Trample the injured and hurdle the dead.
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Your right, using steam would be the most efficient way.
But, I'm shy of boiling water in a sealed vessel.
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

That's what the PRV is for.

15 psi (1 bar) is less than a bicycle tire and you'll likely only need a half bar.
Trample the injured and hurdle the dead.
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

F............. Lbs per sq.inch
212.......... 0.0
214.......... 0.6
216.......... 1.2
218.......... 1.8
220.......... 2.5
222.......... 3.2
224.......... 3.9
226.......... 4.6
228.......... 5.3
230.......... 6.1
232.......... 6.9
234.......... 7.7
236.......... 8.5
Trample the injured and hurdle the dead.
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

LWTCS wrote:Ah,, just saw where you said a thermostatic controlled element. Obviously that would have to go. But 1500 watts would work nicely under 1 bar with that small amount of heating medium to bring to temp.
The thermostat is adjustable to 245f and I have a couple steam rated 15psi relief valves, one of which has been modified to open from 3 to 10psi.
There's also several pressure activated switches in my junk pile that could be used to shut off the heater before over pressure.
The water jacket on the Bain Marie could be easily made into low pressure boiler
But, I'd rather not post about building something as dangerous as a home made, unvented steam boiler. :shock:
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

Sounds like a perfect set up.

Sorry. Not trying to impose.
Trample the injured and hurdle the dead.
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Your ideas are good and I might use them
But I'll do it quietly, don't want any newbie's reading about our bad habits. :lol:
User avatar
LWTCS
Site Mod
Posts: 12837
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 24 gallon electric bain marie

Post by LWTCS »

The vessel appears to be very high quality.
Who made it?
Do you know the wall thickness?
Trample the injured and hurdle the dead.
User avatar
shadylane
Master of Distillation
Posts: 10363
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 24 gallon electric bain marie

Post by shadylane »

Printed on the thermometer is "Candle Equipment Sales" that the only writing on it.
The batteries are dead on the micrometer but it appears to be 14 or 16 gage.
Post Reply