Lower ABV output on pot still with sight glass?
Moderator: Site Moderator
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Lower ABV output on pot still with sight glass?
Hi all,
I've had my alembic pot still for a while as stock. On my last few runs I was, from memory, getting about 70% ABV at the beginning of the run, which declined over time, of course.
I've recently added a sight glass and copper scrubbers to the setup, and run a few stripping runs. All fine, but didn't measure ABV.
I ran my first spirit run last night with the glass, and after measuring ABV found the initial output was closer to 50%.
Not sure why the drop.
A few changes between the 70 and 50 run.
70% runs
Was using a 2000w, 25L boiler.
The last few runs were TPW wash or blackstrap rum.
50% run
Sight glass + Scrubbers
Was using a 2400w, 35L boiler
Rye mash
A few thoughts on contributing factors.
Lower output from the Rye, compared to the basically pure sure TPW and molasses?
I was using a more powerful boiler, but it had only the 1900w element on and was powered down as well, the same as I did before - Maybe it's more efficient though and I'm underestimating the output compared to my last one? It's running hotter than I think, and blasting out more water?
Other people's thoughts?
If anything I'd have thought the sight glass might increase ABV a fraction, what with the scrubbers providing a tiny amount of reflux.
Not sure where the 20% drop has come from.
Cheers all.
I've had my alembic pot still for a while as stock. On my last few runs I was, from memory, getting about 70% ABV at the beginning of the run, which declined over time, of course.
I've recently added a sight glass and copper scrubbers to the setup, and run a few stripping runs. All fine, but didn't measure ABV.
I ran my first spirit run last night with the glass, and after measuring ABV found the initial output was closer to 50%.
Not sure why the drop.
A few changes between the 70 and 50 run.
70% runs
Was using a 2000w, 25L boiler.
The last few runs were TPW wash or blackstrap rum.
50% run
Sight glass + Scrubbers
Was using a 2400w, 35L boiler
Rye mash
A few thoughts on contributing factors.
Lower output from the Rye, compared to the basically pure sure TPW and molasses?
I was using a more powerful boiler, but it had only the 1900w element on and was powered down as well, the same as I did before - Maybe it's more efficient though and I'm underestimating the output compared to my last one? It's running hotter than I think, and blasting out more water?
Other people's thoughts?
If anything I'd have thought the sight glass might increase ABV a fraction, what with the scrubbers providing a tiny amount of reflux.
Not sure where the 20% drop has come from.
Cheers all.
- Stonecutter
- Site Donor
- Posts: 1943
- Joined: Fri Apr 16, 2021 2:40 pm
- Location: Somewhere within the Milkyway
Re: Lower ABV output on pot still with sight glass?
The sight glass and scrubbers aren’t going to do anything by themselves. You’re going to need some sort of reflux “device” to bump up your ABV. To be clear on things, when were you Measuring abv? During the run? Or after? And how were you measuring, were you Using a parrot? Will need more info regarding your rye mash to determine more from that. You used a bigger element and a bigger boiler you may have pushed to hard and smeared, resulting in a lower abv. But who knows. A little bit more info would be helpful.
Freedom had been hunted round the globe; reason was considered as rebellion; and the slavery of fear had made men afraid to think. But such is the irresistible nature of truth, that all it asks, and all it wants, is the liberty of appearing.
-Thomas Paine
-Thomas Paine
- Dancing4dan
- Site Donor
- Posts: 936
- Joined: Sun Oct 18, 2020 4:18 pm
- Location: Alberta
Re: Lower ABV output on pot still with sight glass?
Would be best to post a pic of your set up
"What harms us is to persist in self deceit and ignorance"
Marcus Aurelius
I’m not an alcoholic! I’m a drunk. Alcoholics go to meetings!
Marcus Aurelius
I’m not an alcoholic! I’m a drunk. Alcoholics go to meetings!
- Stonecutter
- Site Donor
- Posts: 1943
- Joined: Fri Apr 16, 2021 2:40 pm
- Location: Somewhere within the Milkyway
Re: Lower ABV output on pot still with sight glass?
How are you controlling your power input? Did you water down your stripping run at all?
Edit: posted same time as Dan
Edit: posted same time as Dan
Freedom had been hunted round the globe; reason was considered as rebellion; and the slavery of fear had made men afraid to think. But such is the irresistible nature of truth, that all it asks, and all it wants, is the liberty of appearing.
-Thomas Paine
-Thomas Paine
Re: Lower ABV output on pot still with sight glass?
Compare the ABVs of the washes.
- jonnys_spirit
- Site Donor
- Posts: 3667
- Joined: Wed Oct 21, 2015 7:58 am
- Location: The Milky Way
Re: Lower ABV output on pot still with sight glass?
Post some pics of your alembic still please. You mention both a 25l and 35l boiler which sounds like two different stills to me. How did you attach a sight glass and mesh to an alembic?
I have a small batch alembic that I get close to 90% out of (upper 80’s) when I run it then it drops off pretty sharply.
Cheers!
-j
I have a small batch alembic that I get close to 90% out of (upper 80’s) when I run it then it drops off pretty sharply.
Cheers!
-j
————
i prefer my mash shaken, not stirred
————
i prefer my mash shaken, not stirred
————
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Re: Lower ABV output on pot still with sight glass?
The 70% and 50% is measuring the first jar, the day after the run. Measured with a standard alcometre.Stonecutter wrote: ↑Mon Jun 27, 2022 4:05 pm To be clear on things, when were you Measuring abv? During the run? Or after? And how were you measuring, were you Using a parrot?
Same 100ml of foreshots discarded from all runs.
Possibly. Will do the next run at lower power and see what that brings.Stonecutter wrote: ↑Mon Jun 27, 2022 4:05 pm You used a bigger element and a bigger boiler you may have pushed to hard and smeared, resulting in a lower abv. But who knows. A little bit more info would be helpful.
-
- Master of Distillation
- Posts: 3387
- Joined: Thu Dec 01, 2016 6:27 pm
- Location: Ontario
Re: Lower ABV output on pot still with sight glass?
You can't compare unless the ABV of each wash is provided, as that's the determining factor..andrew_987789 wrote: ↑Mon Jun 27, 2022 3:29 pm 70% runs
Was using a 2000w, 25L boiler.
The last few runs were TPW wash or blackstrap rum.
50% run
Sight glass + Scrubbers
Was using a 2400w, 35L boiler
Rye mash
Mars
" I know quite certainly that I myself have no special talent. Curiosity, Obsession and dogged endurance, combined with self-criticism, have brought me to my knowledge and understanding "
– Albert Einstein
– Albert Einstein
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Re: Lower ABV output on pot still with sight glass?
A power controller, yes.Stonecutter wrote: ↑Mon Jun 27, 2022 4:07 pm How are you controlling your power input? Did you water down your stripping run at all?
I did actually water it down a bit. Added roughly 3L of water to the boiler with the 25L of wash. Just to reduce the viscosity a bit from the Rye.
This is something I didn't do on the previous runs. Definitely no more than 3L added though.
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Re: Lower ABV output on pot still with sight glass?
Not different stills.jonnys_spirit wrote: ↑Mon Jun 27, 2022 4:40 pm Post some pics of your alembic still please. You mention both a 25l and 35l boiler which sounds like two different stills to me. How did you attach a sight glass and mesh to an alembic?
I previously had a 25L boiler, I now have a 35L boiler.
Everything from the dome up is the same, just more volume and heat below.
I can post back with a pic, but the attachment order was 'Copper dome > sight glass stuff with scrubbers > condenser'. Nothing out of the ordinary.
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Re: Lower ABV output on pot still with sight glass?
I don't have any of the earlier runs wash ABV recorded, unfortunately. Something for next time.StillerBoy wrote: ↑Mon Jun 27, 2022 5:04 pm You can't compare unless the ABV of each wash is provided, as that's the determining factor..
- Stonecutter
- Site Donor
- Posts: 1943
- Joined: Fri Apr 16, 2021 2:40 pm
- Location: Somewhere within the Milkyway
Re: Lower ABV output on pot still with sight glass?
Yeah man, it looks like the small alterations in your protocol ended up giving you different results. As mentioned above, different ABV going in the pot is going to change what comes out. I wouldn’t have worried about the “mouthfeel” of the rye but experimenting makes the hobby fun. Some good advice has been given. Take as many notes as you can and hopefully some of the why’s should become more apparent.
Good luck
Good luck
Freedom had been hunted round the globe; reason was considered as rebellion; and the slavery of fear had made men afraid to think. But such is the irresistible nature of truth, that all it asks, and all it wants, is the liberty of appearing.
-Thomas Paine
-Thomas Paine
- Stonecutter
- Site Donor
- Posts: 1943
- Joined: Fri Apr 16, 2021 2:40 pm
- Location: Somewhere within the Milkyway
Re: Lower ABV output on pot still with sight glass?
I’ve done some snooping and it looks like you’ve been fiddling around with your sight glass for a bit. That sight glass is really nothing more than to help see if you’re flooding, I’m not sure what spurred you to use it without reflux other than to add some more copper in the system. Have you made a run using reflux? I’ve never looked into the t500 and I’m not sure how the reflux works on them. During my 34-40% Spirit runs using a short CM jacket on a 2” column with one small copper packing inside and minimal reflux I pull 85% pretty easily for most of the run.
Freedom had been hunted round the globe; reason was considered as rebellion; and the slavery of fear had made men afraid to think. But such is the irresistible nature of truth, that all it asks, and all it wants, is the liberty of appearing.
-Thomas Paine
-Thomas Paine
-
- Novice
- Posts: 25
- Joined: Fri May 20, 2022 6:29 pm
Re: Lower ABV output on pot still with sight glass?
Yep, understood.Stonecutter wrote: ↑Mon Jun 27, 2022 6:42 pm I’ve done some snooping and it looks like you’ve been fiddling around with your sight glass for a bit. That sight glass is really nothing more than to help see if you’re flooding, I’m not sure what spurred you to use it without reflux other than to add some more copper in the system.
I have been doing some fiddling around for fun, that said, the primary reason for buying the sight glass was visibility when doing black strap molasses runs, because that stuff is a BIIIIIIITCH for suddenly puking.
As well as adding some copper in the vapor path, as you said.
I'm not expecting the sight glass to do wild and wonderful things, or convert one type of still into another. I was just surprised a bit surprised to see such a difference in that first jar's ABV from one run to the next.
Just asking/triple checking in case I've missed something
Difficult to pinpoint a cause when you've changed a number of things from one process to the next though, I realize.
- Stonecutter
- Site Donor
- Posts: 1943
- Joined: Fri Apr 16, 2021 2:40 pm
- Location: Somewhere within the Milkyway
Re: Lower ABV output on pot still with sight glass?
I hear you loud and clear man. As we venture down the rabbit hole eh?
Freedom had been hunted round the globe; reason was considered as rebellion; and the slavery of fear had made men afraid to think. But such is the irresistible nature of truth, that all it asks, and all it wants, is the liberty of appearing.
-Thomas Paine
-Thomas Paine
-
- Site Donor
- Posts: 1815
- Joined: Wed Dec 30, 2020 10:17 pm
- Location: Northwest France
Re: Lower ABV output on pot still with sight glass?
I would have thought the abv going in was the most obvious candidate. Most sugar wash recipes seem to produce around 10% abv whereas I wouldn't expect to get much above 7% for an AG mash. That's obviously going to effect your abv coming out on a pot still.
"I have a potstill that smears like a fresh plowed coon on the highway" - Jimbo
A little spoon feeding *For New & Novice Distillers
A little spoon feeding *For New & Novice Distillers
-
- Master of Distillation
- Posts: 3387
- Joined: Thu Dec 01, 2016 6:27 pm
- Location: Ontario
Re: Lower ABV output on pot still with sight glass?
He got lots to learn yet, but haven't learn the basic yet of why the boiler load abv and volume determine the alcohol content and behavior is important in a spirit pot run.. hopefully he's learn somethings with this experience..NormandieStill wrote: ↑Mon Jun 27, 2022 9:00 pm I would have thought the abv going in was the most obvious candidate. Most sugar wash recipes seem to produce around 10% abv whereas I wouldn't expect to get much above 7% for an AG mash. That's obviously going to effect your abv coming out on a pot still.
The good thing was that he's mindful there was a difference.. there's hope..
Mars
" I know quite certainly that I myself have no special talent. Curiosity, Obsession and dogged endurance, combined with self-criticism, have brought me to my knowledge and understanding "
– Albert Einstein
– Albert Einstein
- EricTheRed
- Site Donor
- Posts: 1108
- Joined: Wed Oct 13, 2021 10:49 pm
- Location: South Africa
Re: Lower ABV output on pot still with sight glass?
my personal experience - the more power you put in, the lower the ABV
So you have gone from 1900W to 2400W, the abv will be lower as you are pulling more water along
ta
So you have gone from 1900W to 2400W, the abv will be lower as you are pulling more water along
ta
My fekking eyes are bleeding! Installed BS Filters - better! :D
Life has gotten interesting!
Life has gotten interesting!
- Twisted Brick
- Master of Distillation
- Posts: 3798
- Joined: Sat Mar 09, 2013 4:54 pm
- Location: Craigh Na Dun
Re: Lower ABV output on pot still with sight glass?
On a pot still spirit run, the difference in boiler-charge volumes doesn't change the boiling temp (Raoult's Law) of identical still charges, regardless of the power applied. Like others have alluded to, the large disparity in the OP's two initial takeoff ABV's should have pointed directly to the difference in starting ABV's as the culprit.
“Always carry a flagon of whiskey in case of snakebite, and furthermore, always carry a small snake.”
- W.C. Fields
My EZ Solder Shotgun
My Steam Rig and Manometer
- W.C. Fields
My EZ Solder Shotgun
My Steam Rig and Manometer
-
- Master of Distillation
- Posts: 3387
- Joined: Thu Dec 01, 2016 6:27 pm
- Location: Ontario
Re: Lower ABV output on pot still with sight glass?
Very important point stated there TB..Twisted Brick wrote: ↑Tue Jun 28, 2022 8:26 am On a pot still spirit run, the difference in boiler-charge volumes doesn't change the boiling temp (Raoult's Law) of identical still charges, regardless of the power applied.
It should be one of the first things a beginner be requires to learn, but most never learn to monitor their low wine ABV levels prior to the spirit run..
When I read threads like this one, it me wonder how they are able to determine where they're at during the run..
Mars
" I know quite certainly that I myself have no special talent. Curiosity, Obsession and dogged endurance, combined with self-criticism, have brought me to my knowledge and understanding "
– Albert Einstein
– Albert Einstein