2"-3" triclover sourcing

Research sources, reviews and links to information relating to distillation.

Moderator: Site Moderator

2"-3" triclover sourcing

Postby UnSub » Sat Jan 16, 2016 1:58 pm

(I really must be inept at using a search engine, I'm admitting it now)I have been reading A LOT on this form and just seen someone mention a source for the keg-to-3" triclamp reducer that was much cheaper than Brewhaus et.al. I need the clamps and seals to attach 3" boka build to this 15.5 sanke keg. Honestly, I have been looking for a while and can't find it- can someone help a brother out?;)
Regards,
UnSub
Last edited by UnSub on Sat Jan 16, 2016 2:20 pm, edited 2 times in total.
User avatar
UnSub
Site Donor
Site Donor
 
Posts: 165
Joined: Tue Jan 12, 2016 4:04 pm

Re: 2"-3" triclover sourcing

Postby jedneck » Sat Jan 16, 2016 2:02 pm

welcome aboard some of us are ornery old coots but if you do a lot of
reading and don't ask stupid questions you'll be alright most are
big help
Dunder
User avatar
jedneck
Site Donor
Site Donor
 
Posts: 3551
Joined: Thu Jan 10, 2013 5:16 pm
Location: drive to the sticks, hang a right past the sticks amd go a couple more miles.

Re: 2"-3" triclover sourcing

Postby FreeMountainHermit » Sat Jan 16, 2016 2:17 pm

The cap style reducer offers a little less height as well as being a couple of bucks cheaper.

https://www.brewershardware.com/Tri-Clo ... 30X20.html
Blah, blah, blah,........
User avatar
FreeMountainHermit
Site Donor
Site Donor
 
Posts: 1772
Joined: Thu May 12, 2011 6:45 pm
Location: Two Dogs Holler, West Virginia

Re: 2"-3" triclover sourcing

Postby Swedish Pride » Sat Jan 16, 2016 2:27 pm

Ali express is the same, only difference is that you get to wait for a month to get it
http://www.aliexpress.com/item/76MM-to- ... 18400_6148
Don't be a dick
User avatar
Swedish Pride
Site Donor
Site Donor
 
Posts: 2049
Joined: Tue Aug 26, 2014 2:16 am
Location: Emerald Isle

Re: 2"-3" triclover sourcing

Postby LWTCS » Sat Jan 16, 2016 3:59 pm

Trample the injured and hurdle the dead.
User avatar
LWTCS
Site Donor
Site Donor
 
Posts: 9983
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 2"-3" triclover sourcing

Postby varocketry » Mon Aug 08, 2016 9:49 am

Best source I've found by far is a chinese vendor selling direct on EBAY. I've used him several times.

http://www.ebay.com/itm/SANITARY-ASSEMB ... xycmBSsx55

http://www.ebay.com/itm/8-End-Cap-8-Wel ... SwBLlVExa9
-Just need something else to build. -
User avatar
varocketry
Site Donor
Site Donor
 
Posts: 520
Joined: Fri Mar 22, 2013 5:15 pm
Location: somewhere not near Detroit

Re: 2"-3" triclover sourcing

Postby LWTCS » Mon Aug 08, 2016 10:11 am

Not at all the best prices.
Trample the injured and hurdle the dead.
User avatar
LWTCS
Site Donor
Site Donor
 
Posts: 9983
Joined: Mon Jan 26, 2009 6:04 pm
Location: North Palm Beach

Re: 2"-3" triclover sourcing

Postby Snackson » Mon Aug 08, 2016 2:36 pm

varocketry wrote:Best source I've found by far is a chinese vendor selling direct on EBAY. I've used him several times.

http://www.ebay.com/itm/SANITARY-ASSEMB ... xycmBSsx55

http://www.ebay.com/itm/8-End-Cap-8-Wel ... SwBLlVExa9

Their stuff doesn't match up to standard sizes I have found. For example, ordered the 6", soldered it up, bought a 6" reducer from Glacier and they are different sizes. I would avoid the daily appliance vendor. Buy from Larry, at least there you have quality service from a reputable vendor.
User avatar
Snackson
Site Donor
Site Donor
 
Posts: 495
Joined: Mon Jun 23, 2014 8:03 pm

Re: 2"-3" triclover sourcing

Postby Hank Reardon » Mon Aug 08, 2016 7:47 pm

I mistakenly did the Chinese version. Both clamps have failed (all thread bent). I have ordered fro SD and received premium quality.

The ones you want are those that have a hole through the thumb handle.
Hank Reardon
Site Donor
Site Donor
 
Posts: 395
Joined: Thu Apr 21, 2016 8:02 pm


Return to Resources and Reviews



Who is online

Users browsing this forum: No registered users and 1 guest