Exracting NGS from steel drum
Moderator: Site Moderator
-
- Novice
- Posts: 22
- Joined: Tue Oct 22, 2019 8:12 am
Exracting NGS from steel drum
Hi there fellow distillers. Hope everyone is keeping well?
I have a question regarding extracting NGS from a steel drum. Namely, how on earth do I do it? I've been purchasing NGS in 25 litre containers which are easy to pour into my measuring vessel. However the steel drum weighs about 150kg's (400 pounds). My guess is I need to funnel it out? Or maybe use a syringe (glass or stainless steel). What happens when I need to extract from deep, what material do I use? I don't want to contaminate the alcohol with chemicals.
I can only apologise for how stupid I must sound to you guys. Again, all your comments good and bad are hugely appreciated.
Warm regards,
Mark
I have a question regarding extracting NGS from a steel drum. Namely, how on earth do I do it? I've been purchasing NGS in 25 litre containers which are easy to pour into my measuring vessel. However the steel drum weighs about 150kg's (400 pounds). My guess is I need to funnel it out? Or maybe use a syringe (glass or stainless steel). What happens when I need to extract from deep, what material do I use? I don't want to contaminate the alcohol with chemicals.
I can only apologise for how stupid I must sound to you guys. Again, all your comments good and bad are hugely appreciated.
Warm regards,
Mark
Re: Exracting NGS from steel drum
In a commercial setting I'd say they probably have a barrel lift, but assuming you don't, I'd use a syphon.
You'll need:
3/8 or 1/2" soft copper tube i.e. no plastic
Two hole bung of appropriate size
Collection container
Put a longer piece of tube through the bung so that one end nearly reaches the bottom of the barrel and the other is resting in your collection container beside or lower than the barrel. Put a short piece of pipe in the second bung hole (LoL) and push the bung into the hole so it seals. Apply air pressure to the short pipe to start the syphon, block it to stop. Done.
You'll need:
3/8 or 1/2" soft copper tube i.e. no plastic
Two hole bung of appropriate size
Collection container
Put a longer piece of tube through the bung so that one end nearly reaches the bottom of the barrel and the other is resting in your collection container beside or lower than the barrel. Put a short piece of pipe in the second bung hole (LoL) and push the bung into the hole so it seals. Apply air pressure to the short pipe to start the syphon, block it to stop. Done.
_____________________
EXPAT
Current boiler and pot head
Cross flow condenser
Modular 3" Boka - pics tbd
___________________
EXPAT
Current boiler and pot head
Cross flow condenser
Modular 3" Boka - pics tbd
___________________
-
- Master of Distillation
- Posts: 4666
- Joined: Sun Aug 27, 2006 4:48 am
- Location: Northern Victoria, Australia
Re: Exracting NGS from steel drum
You could use air pressure.
With an oil-free compressor and a low pressure.
Geoff
With an oil-free compressor and a low pressure.
Geoff
The Baker
- hypnopooper
- Bootlegger
- Posts: 119
- Joined: Mon Jul 23, 2012 4:45 pm
Re: Exracting NGS from steel drum
Not sure about wether the aluminum or cast iron crank case will have an issue, but something like this would do the job...
This one is stainless and might be a better solution...
https://www.uline.com/Product/Detail/H- ... lsrc=aw.ds
This one is stainless and might be a better solution...
https://www.uline.com/Product/Detail/H- ... lsrc=aw.ds
Re: Exracting NGS from steel drum
Get a drum cradle.
-
- Novice
- Posts: 22
- Joined: Tue Oct 22, 2019 8:12 am
Re: Exracting NGS from steel drum
Thanks very much for replying to my message, I really appreciate it. Kind regards,Expat wrote: ↑Sun May 03, 2020 4:31 am In a commercial setting I'd say they probably have a barrel lift, but assuming you don't, I'd use a syphon.
You'll need:
3/8 or 1/2" soft copper tube i.e. no plastic
Two hole bung of appropriate size
Collection container
Put a longer piece of tube through the bung so that one end nearly reaches the bottom of the barrel and the other is resting in your collection container beside or lower than the barrel. Put a short piece of pipe in the second bung hole (LoL) and push the bung into the hole so it seals. Apply air pressure to the short pipe to start the syphon, block it to stop. Done.
Mark
-
- Novice
- Posts: 22
- Joined: Tue Oct 22, 2019 8:12 am
-
- Novice
- Posts: 22
- Joined: Tue Oct 22, 2019 8:12 am
Re: Exracting NGS from steel drum
Thanks very much for this. I have found one in the UK that is compatible with alcohol. I've purchased this and it will be arriving in a week or so. You're a legend.hypnopooper wrote: ↑Sun May 03, 2020 12:00 pm Not sure about wether the aluminum or cast iron crank case will have an issue, but something like this would do the job...
This one is stainless and might be a better solution...
https://www.uline.com/Product/Detail/H- ... lsrc=aw.ds
Mark
-
- Novice
- Posts: 22
- Joined: Tue Oct 22, 2019 8:12 am