Removing Sankey keg valves...

Moderator: Site Moderator

Post Reply
dixiedrifter
Swill Maker
Posts: 338
Joined: Wed Aug 16, 2006 11:59 pm

Removing Sankey keg valves...

Post by dixiedrifter »

Here is a simple guide to removing sankey keg valves.

Step 1: You must depressurise the keg first. Depressurize the keg by pushing down on the ball in the center of the valve. This can get messy, especially if there is any beer in the keg, and it takes a bit of pressure so I did not take a pic.

Lie the keg on its side and point the valve away from anything important, like your face, or the house.

Step 2: Using a screwdriver thats had a little work done on it by a bench grinder, hammer it in the little opening of the spring and pry the spring upwards. Ignore the big glaring warning on the top of the keg about removing the valve. :wink:
Removing Sankey Valve 1.jpg
Removing Sankey Valve 2.jpg

Step 3: Get the screwdriver up in under the ring and follow it around and remove the ring. Notice the end of the spring and how the screwdriver head is shaped. Both are tapered.
Removing Sankey Valve 3.jpg

Step 4: Notice the valve is in its locked position. To remove the valve it will be necessary to beat on it with a hammer to move it to the unlocked position.
Removing Sankey Valve 4.jpg
Removing Sankey Valve 5.jpg
Removing Sankey Valve 6.jpg
Step 5: Lift up the valve. It should easily come loose with just the tip of your finger, and will come loose with great force on its own if you forgot to depressurize the keg first!
Removing Sankey Valve 7.jpg
Thats it. With a little bit of practice you can have one loose in less than a minute with nothing more than a screwdriver or hammer.
mikeac
Swill Maker
Posts: 349
Joined: Thu Dec 21, 2006 5:57 pm
Location: an island off a west coast

Post by mikeac »

Just a reminder to de-presurize the keg with somthign other then your hand...apparently there could be a lot of pressure in there
Don't take life too seriously -- you'll never get out of it alive.
HookLine
retired
Posts: 5628
Joined: Sun May 13, 2007 8:38 am
Location: OzLand

Post by HookLine »

Excellent tutorial.

I vote for this one being made a sticky.

The only thing I would change is to give a clearer warning at the beginning about the dangers of not completely releasing the pressure, and a good explanation (including pics) about how to do it safely (outside, with the valve pointing away from you, wearing safety goggles, etc).
Be safe.
Be discreet.
And have fun.
cannon.co.tn
Swill Maker
Posts: 196
Joined: Fri Jul 20, 2007 3:14 pm

Post by cannon.co.tn »

Nice pictures. This would have made my first attempt much easier.


You can use a smaller screwdriver to start the removal so you don't have to grind an otherwise decent screwdriver
bourbonbob
Angel's Share
Angel's Share
Posts: 449
Joined: Thu Sep 28, 2006 12:55 am
Location: Beyond the Black Stump Australia

Post by bourbonbob »

I've removed the stems from 3 sankey type kegs now, I have become rather good at it, the last one I done took about 30 seconds.
Image Keep on Stillin' Image
dixiedrifter
Swill Maker
Posts: 338
Joined: Wed Aug 16, 2006 11:59 pm

Post by dixiedrifter »

Actually using your finger to push down on the big ball in the center is probably the safest way to go since there is nothing that can slip... if it don't want to push down you need to use some sort of tool. It don't really matter. Just remember, if there is any beer in the keg, you will get drownded.

Yeah and a pair of gloves helps out too. First one I did I cut my finger pretty good on the retaining ring.

The screwdriver was already toast from over torquing it so I just ground it down.

BTW, you can't (you can but it makes it harder) use a normal screwdriver as it won't engage the spring correctly
User avatar
Husker
retired
Posts: 5031
Joined: Thu Aug 17, 2006 1:04 pm

Post by Husker »

One thing I have found that works good to remove pressure from a keg, is to put a thick towel over the valve opening, and then use a hammer handle (I like using a ball peen, since there is no claw with sharp edges). The ball peen gives you a good handle to hold on to, and the end of the wooden handle will push the ball down pretty easily (unless the pressure is EXTREME).

This will release the pressure, without having your hand (finger) around any sharp edges), and will keep most of the stinky old beer from shooting all over you (P.U.)

H.
BW Redneck
Trainee
Posts: 775
Joined: Sun Dec 10, 2006 11:57 am
Location: 1000 acre farm, Ohio

Post by BW Redneck »

HookLine wrote:Excellent tutorial.

I vote for this one being made a sticky.

The only thing I would change is to give a clearer warning at the beginning about the dangers of not completely releasing the pressure, and a good explanation (including pics) about how to do it safely (outside, with the valve pointing away from you, wearing safety goggles, etc).
I second that. :)
"If you can't dazzle them with brilliance... baffle them with bullshit."
"Don't steal. The government hates competition."
"Believe none of what you hear, and only half of what you see"

20lt small pot still, working on keg
CoopsOz
Distiller
Posts: 1172
Joined: Wed Aug 16, 2006 4:00 am
Location: Didjabringyabongalong

Post by CoopsOz »

Props to Dixie, good tutorial.
It is most absurdly said, in popular language, of any man, that he is disguised in liquor; for, on the contrary, most men are disguised by sobriety. ~Thomas de Quincy, Confessions of an English Opium-Eater, 1856
junkyard dawg
Master of Distillation
Posts: 3086
Joined: Fri Feb 03, 2006 11:40 am
Location: Texas

Post by junkyard dawg »

Nice work.
HookLine
retired
Posts: 5628
Joined: Sun May 13, 2007 8:38 am
Location: OzLand

Re: Removing Sankey keg valves...

Post by HookLine »

A good demonstration video here (by absinthe, I think):

http://www.youtube.com/watch?v=3G7Ypf5Ojno" onclick="window.open(this.href);return false;" rel="nofollow

And some others:

http://www.youtube.com/watch?v=0_eXacIlsKE" onclick="window.open(this.href);return false;" rel="nofollow
http://www.youtube.com/watch?v=npUA8DvngVw" onclick="window.open(this.href);return false;" rel="nofollow

Don't forget to relieve the gas pressure inside it first!
Be safe.
Be discreet.
And have fun.
blanikdog
Angel's Share
Angel's Share
Posts: 4545
Joined: Tue Aug 09, 2005 11:55 pm
Location: Bullamakanka, Oztrailya

Re: Removing Sankey keg valves...

Post by blanikdog »

The first time I relieved the pressure in a keg I had the keg standing upright. With my second keg I left it on its side.

The second time took far less time as I didn't have to shower and change my clothing immediately afterwards. :roll:

blanik
Simple potstiller. Slow, single run.
(50 litre, propane heated pot still. Coil in bucket condenser - No thermometer, No carbon)
The Reading Lounge AND the Rules We Live By should be compulsory reading

Cumudgeon and loving it.
Lothar
Novice
Posts: 16
Joined: Tue Jan 22, 2008 1:30 pm

easy as pie

Post by Lothar »

cannon.co.tn wrote:You can use a smaller screwdriver to start the removal so you don't have to grind an otherwise decent screwdriver
Husker wrote:One thing I have found that works good to remove pressure from a keg, is to put a thick towel over the valve opening, and then use a hammer handle (I like using a ball peen, since there is no claw with sharp edges). The ball peen gives you a good handle to hold on to, and the end of the wooden handle will push the ball down pretty easily (unless the pressure is EXTREME).H.
Thanks everyone! With this tutorial it only took about 10 minutes without any special tools on my first try.
Attachments
nomovalve.JPG
adama_bill
Novice
Posts: 60
Joined: Mon Mar 23, 2009 12:25 am
Location: OzLand - South

Re: Removing Sankey keg valves...

Post by adama_bill »

I like the screw driver idea ~ I've sure broken a few drill bits trying to make a hole in that s/s retaining ring (as per some youtube videos).
User avatar
heynonny
Swill Maker
Posts: 464
Joined: Fri Jun 06, 2008 7:17 am
Location: SoCal

Re: Removing Sankey keg valves...

Post by heynonny »

One can use an about 7/8- 1" open end wrench, catch it on one of the two little 'nubs' sticking out of the valve-plug unit to relieve pressure. This way you can relieve thepressure -s-l-o-w-l-y, and then stick a piece of wire (a short piece of insulated house wiring works well) down to keep the valve open. Like blanik says, do it sideways in theres anything inside. I use two icepicks to get the circlip out and then use a small screwdriver to remove it -hey-
  
 
 
       Oh,look!! Its a hole in the space-time contuum!!
chaos
Novice
Posts: 21
Joined: Thu Aug 05, 2010 10:14 pm

Re: Removing Sankey keg valves...

Post by chaos »

dixiedrifter wrote:Here is a simple guide to removing sankey keg valves.

Step 1: You must depressurise the keg first. Depressurize the keg by pushing down on the ball in the center of the valve. This can get messy, especially if there is any beer in the keg, and it takes a bit of pressure so I did not take a pic.

Lie the keg on its side and point the valve away from anything important, like your face, or the house.

Step 2: Using a screwdriver thats had a little work done on it by a bench grinder, hammer it in the little opening of the spring and pry the spring upwards. Ignore the big glaring warning on the top of the keg about removing the valve. :wink:
Removing Sankey Valve 1.jpg
Removing Sankey Valve 2.jpg

Step 3: Get the screwdriver up in under the ring and follow it around and remove the ring. Notice the end of the spring and how the screwdriver head is shaped. Both are tapered.
Removing Sankey Valve 3.jpg

Step 4: Notice the valve is in its locked position. To remove the valve it will be necessary to beat on it with a hammer to move it to the unlocked position.
Removing Sankey Valve 4.jpg
Removing Sankey Valve 5.jpg
Removing Sankey Valve 6.jpg
Step 5: Lift up the valve. It should easily come loose with just the tip of your finger, and will come loose with great force on its own if you forgot to depressurize the keg first!
Removing Sankey Valve 7.jpg
Thats it. With a little bit of practice you can have one loose in less than a minute with nothing more than a screwdriver or hammer.
would u happen to know if the 50L kegr have the same set up? and do u have any idear on how to obtain these?
ozone39
Rumrunner
Posts: 659
Joined: Sat Dec 12, 2009 9:14 am
Location: Big Sky Country

Re: Removing Sankey keg valves...

Post by ozone39 »

A 2 5/8" hole saw fits around the whole thing...
thinking inside the box is for squares....
ScottishBoy
Site Donor
Site Donor
Posts: 1283
Joined: Wed Oct 21, 2009 9:53 am
Location: Just underneath this group of pixels...;)

Re: Removing Sankey keg valves...

Post by ScottishBoy »

adama_bill wrote:I like the screw driver idea ~ I've sure broken a few drill bits trying to make a hole in that s/s retaining ring (as per some youtube videos).
If you dont want to sacrifice a screw driver, you can also use a 10 penny nail. I went after it with a bench grinder to put a point on it like a screwdriver which just happens to fit the little divot on the throat. Stick it in and pry to the side and the SS coil will pop right out and you havent lost anything or had to sacrifice a tool. Then just follow it around like the tutorial said.
ScottishBoy
HD Survival in a Nutshell...
Read.Search.Listen.Ask for feedback, you WILL get it. Plastic is always "questionable". Dont hurry. Be Careful. Dont Sell,Tell, or Yell. If you wouldnt serve it to your friends, then it isnt worth keeping.
elliott
Novice
Posts: 2
Joined: Sat Dec 05, 2009 2:01 pm

Re: Removing Sankey keg valves...

Post by elliott »

Hi all, just picked upan old miller keg at the scrapyard. looks like the same sankey valve, but no spring thingey. i assumt it unscrews, but i can't get it to budge. anyone have experience with one of these?
maheel
Site Donor
Site Donor
Posts: 936
Joined: Mon Jan 26, 2009 11:25 pm
Location: OZtralia in the lower half

Re: Removing Sankey keg valves...

Post by maheel »

Image

what one is it?

or left to right which one ?
Image
elliott
Novice
Posts: 2
Joined: Sat Dec 05, 2009 2:01 pm

Re: Removing Sankey keg valves...

Post by elliott »

haven't tried it yet but this link might do the trick:

http://www.homebrewtalk.com/f35/how-rem ... ing-76393/" onclick="window.open(this.href);return false;" rel="nofollow

oops! maybe that isnt a link. not too good at this computer stuff. elliott
Ono Nadagin
Novice
Posts: 13
Joined: Mon Jun 28, 2010 10:02 am
Location: Republic of Texas

Re: Removing Sankey keg valves...

Post by Ono Nadagin »

Since I just did This for the 1st time myself last week, I wanted to add something I learned that was not mentioned in the videos.

I was able to get the retaining spring clip out and was able to turn the valve so the tabs met the holes and could lift it up to where the tabs were even in the holes but that is as far as it would come out... I made a little tool hung it from a rafter on a cable then put the tool under the little tabs you used to rotate the vale then let the keg hang from the ceiling and with a little downward force it came out.

Now if was basically 'dried beer glued' in... the portion of the valves had some sticky dried beer on it and as it came into contact with the inside of the neck of the keg it hung up enough I couldn't get it out by hand.

Having said all that I think pouring some warm soapy water onto the top of the valve a few times allowing it to penetrate as much as possible would have softened the dried on beer enough and also lubricated the machined surfaces of teh neck and valve would have come out by hand.
absinthe
Rumrunner
Posts: 534
Joined: Sun Jun 25, 2006 8:29 am
Location: Aussie

Re: Removing Sankey keg valves...

Post by absinthe »

http://www.youtube.com/watch?v=mywdx-l2VJY" onclick="window.open(this.href);return false;" rel="nofollow
Whiskey, the most popular of the cold cures that don't work (Leonard Rossiter)
758759754
Novice
Posts: 42
Joined: Mon Jan 17, 2011 2:32 pm

Re: Removing Sankey keg valves...

Post by 758759754 »

Someone said it above, but I'd like to say that a wrench/spanner is the best tool for opening the valve. If I recall correctly, it was 22mm. Put the one end under the little tab and use the bump to push it in. Best part, if you lie down the keg, it naturally puts you out of the way of danger.

Check out this video for a better description of what I'm trying to say:

http://www.youtube.com/watch?v=mywdx-l2VJY" onclick="window.open(this.href);return false;" rel="nofollow

Right around 2:25
Post Reply