I'm wanting to build a 2" Shotgun Condenser and have a couple of questions.
1. Can the inner tubes of the condenser be soft soldered to the end plates or do they have to be brazed?
2. I'm trying to determine the length, would I be correct in assuming that I can use the parent site calculator for a liebig and divide the length by the number of tubes?
I have a 50L keg as my boiler with a rated max of 5000w, weather it actually gets to that is another story.
2" Shotgun Build
Moderator: Site Moderator
- ShineonCrazyDiamond
- Global moderator
- Posts: 3546
- Joined: Thu Feb 27, 2014 6:14 pm
- Location: Look Up
Re: 2" Shotgun Build
4 1/2" tubes, 24" long will knock down anything 5500w counter ever dream of throwing at it. I would think almost double.
http://homedistiller.org/forum/viewtopi ... lit=+Santa
Soft soldered the whole thing. Took a little patience and thought process because of all soft, but this idiot was able to do it.
http://homedistiller.org/forum/viewtopi ... lit=+Santa
Soft soldered the whole thing. Took a little patience and thought process because of all soft, but this idiot was able to do it.
"Come on you stranger, you legend, you martyr, and shine!
You reached for the secret too soon, you cried for the moon.
Shine on you crazy diamond."
You reached for the secret too soon, you cried for the moon.
Shine on you crazy diamond."
- bluefish_dist
- Distiller
- Posts: 1503
- Joined: Fri Jan 16, 2015 10:13 am
- Location: Eastern Ia
Re: 2" Shotgun Build
I made one with 4 1/2" pipes. I did not baffle it and it did not knock down anywhere near 5500w. I used soft solder and had a hard time getting the tubes to seal. Looking back I would have been way ahead to simply use stainless steel gas line for a RC. Cheaper and much easier to make.
I use stilldragon shotguns for PC's 7 tubes in them and they will easily condense 5500w as a product condenser. They have the long ones on clearance.
I use stilldragon shotguns for PC's 7 tubes in them and they will easily condense 5500w as a product condenser. They have the long ones on clearance.
Formerly
Dsp-CO-20051
Dsp-CO-20051
-
Opdog
- Swill Maker
- Posts: 167
- Joined: Sat Aug 17, 2013 6:02 pm
Re: 2" Shotgun Build
Mine is very similar to SoCD's. 4 1/2 tubes at 24" long coped at the bottom. Originally I had solder throughout. I recently took it apart as part of a recent upgrade. I'm in the process of putting it back together now. This time I used Silfos brazing rings on the inside of each end plate where the tubes meet the plate. I had to use MAP gas to get the endplate and tube hot enough. I expect that soldering the end plates will be muuuch easier than the last time. I had pinholes everywhere the first time and spent hours running the end plates. The brazing rings were very easy to use, just remember to use the outside pipe diameter when ordering.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I've stopped fighting my inner demons. We are on the same side now.
-
Opdog
- Swill Maker
- Posts: 167
- Joined: Sat Aug 17, 2013 6:02 pm
Re: 2" Shotgun Build
That should say tinning the endplates
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I've stopped fighting my inner demons. We are on the same side now.
-
KiwiArmour
- Novice
- Posts: 23
- Joined: Sat Jul 11, 2015 1:42 pm
Re: 2" Shotgun Build
Another question does it need to be run vertical or can it be put at an angle?