2" Shotgun Build

Post your builds here.

Moderator: Site Moderator

Post Reply
KiwiArmour
Novice
Posts: 23
Joined: Sat Jul 11, 2015 1:42 pm

2" Shotgun Build

Post by KiwiArmour »

I'm wanting to build a 2" Shotgun Condenser and have a couple of questions.

1. Can the inner tubes of the condenser be soft soldered to the end plates or do they have to be brazed?
2. I'm trying to determine the length, would I be correct in assuming that I can use the parent site calculator for a liebig and divide the length by the number of tubes?

I have a 50L keg as my boiler with a rated max of 5000w, weather it actually gets to that is another story.
User avatar
ShineonCrazyDiamond
Global moderator
Posts: 3546
Joined: Thu Feb 27, 2014 6:14 pm
Location: Look Up

Re: 2" Shotgun Build

Post by ShineonCrazyDiamond »

4 1/2" tubes, 24" long will knock down anything 5500w counter ever dream of throwing at it. I would think almost double.

http://homedistiller.org/forum/viewtopi ... lit=+Santa

Soft soldered the whole thing. Took a little patience and thought process because of all soft, but this idiot was able to do it. :thumbup:
"Come on you stranger, you legend, you martyr, and shine!
You reached for the secret too soon, you cried for the moon.
Shine on you crazy diamond."
KiwiArmour
Novice
Posts: 23
Joined: Sat Jul 11, 2015 1:42 pm

Re: 2" Shotgun Build

Post by KiwiArmour »

Thanks
User avatar
bluefish_dist
Distiller
Posts: 1503
Joined: Fri Jan 16, 2015 10:13 am
Location: Eastern Ia

Re: 2" Shotgun Build

Post by bluefish_dist »

I made one with 4 1/2" pipes. I did not baffle it and it did not knock down anywhere near 5500w. I used soft solder and had a hard time getting the tubes to seal. Looking back I would have been way ahead to simply use stainless steel gas line for a RC. Cheaper and much easier to make.
I use stilldragon shotguns for PC's 7 tubes in them and they will easily condense 5500w as a product condenser. They have the long ones on clearance.
Formerly
Dsp-CO-20051
Opdog
Swill Maker
Posts: 167
Joined: Sat Aug 17, 2013 6:02 pm

Re: 2" Shotgun Build

Post by Opdog »

Mine is very similar to SoCD's. 4 1/2 tubes at 24" long coped at the bottom. Originally I had solder throughout. I recently took it apart as part of a recent upgrade. I'm in the process of putting it back together now. This time I used Silfos brazing rings on the inside of each end plate where the tubes meet the plate. I had to use MAP gas to get the endplate and tube hot enough. I expect that soldering the end plates will be muuuch easier than the last time. I had pinholes everywhere the first time and spent hours running the end plates. The brazing rings were very easy to use, just remember to use the outside pipe diameter when ordering.


Sent from my iPhone using Tapatalk
I've stopped fighting my inner demons. We are on the same side now.
Opdog
Swill Maker
Posts: 167
Joined: Sat Aug 17, 2013 6:02 pm

Re: 2" Shotgun Build

Post by Opdog »

That should say tinning the endplates


Sent from my iPhone using Tapatalk
I've stopped fighting my inner demons. We are on the same side now.
KiwiArmour
Novice
Posts: 23
Joined: Sat Jul 11, 2015 1:42 pm

Re: 2" Shotgun Build

Post by KiwiArmour »

Another question does it need to be run vertical or can it be put at an angle?
Post Reply