which still design for 11 gal keg

Vapor, Liquid or Cooling Management. Flutes, plates, etc.

Moderator: Site Moderator

Post Reply
nick9one1
Novice
Posts: 20
Joined: Mon Apr 13, 2009 11:00 am

which still design for 11 gal keg

Post by nick9one1 »

I'm planning on building a still from a 11 gal keg (which I already have).
I also have a SSVR and 6kW element setup.

I was planning on building a mini boka with a 2 inch x 3 foot column. I could go bigger but the price of copper over here is quite high.

But after reading a few comparisons on LM, VM and CM. It sounds like VM is a better design giving more control.

There are lots of designs around for the boka, with exact measurements sizes etc.
I cant really find the same for a 2" VM.

So can anyone point me to some good 2" VM plans?

Also, I can go to 2.5" but I was planning on using a 2" triclamp on the keg connector.
Would this create a bottleneck and make the larger column pointless?

something like this;
Image
png image maker app
Last edited by nick9one1 on Thu May 12, 2022 11:08 am, edited 2 times in total.
User avatar
Ben
Distiller
Posts: 1292
Joined: Mon Oct 05, 2020 6:13 am
Location: Colorado

Re: which still design for 5gal keg

Post by Ben »

Your triclamp is fine, it will allow you to go to a larger keg later. The bottle neck is not an issue, vapor will accelerate through the bottle neck then slow back down when it enters the column.

Just pick what still does what you want, and can be built with your skills/tools.
:)
Oatmeal
Swill Maker
Posts: 362
Joined: Sat Jun 19, 2021 5:28 am
Location: Colordo

Re: which still design for 5gal keg

Post by Oatmeal »

If you want to do some pot stilling too, a boka would provide more versatility in my opinion. Going larger diameter, if you can, is worth it too!
Through the magic of alchemy, our spirits live on.
User avatar
bunny
Swill Maker
Posts: 412
Joined: Fri Jun 26, 2020 8:28 am

Re: which still design for 5gal keg

Post by bunny »

Hi!

Is this 5 gal boiler in addition to the 50l you mention here? viewtopic.php?f=85&t=87202

Where have you been and what have you been doing for the last 13 years?

Curious minds want to know. :D
User avatar
Salt Must Flow
Master of Distillation
Posts: 3151
Joined: Sat Jan 29, 2022 2:06 pm
Location: Wuhan China (Novel Coronavirus Laboratory)

Re: which still design for 5gal keg

Post by Salt Must Flow »

It's easy to scale down basic still designs. For a VM, just go with a 2" column, 2" tee, reduce down to a 1" gate valve. Precisely how you do it will likely make very little if not any difference in how it behaves. You will benefit with a taller column.

For instance I went with a short tee so the vapor takeoff wouldn't be unnecessarily long. I made and installed/soldered a copper thermowell into the reducer so I can monitor the vapor takeoff temp.
tri-clamp short tee.png
I went into this hobby knowing I'll likely be doing this for a good number of years so I stepped up to a 3" column rather than a 2". I wasn't going to commit to a 4" because I wasn't confident I'd have multiple 240V circuits at the time and I already had 15.5 gal kegs for boilers. 3" is faster producing than 2" and I'm glad I made it larger. If copper is more expensive then just go with stainless Tri-Clamp spools instead. Multiple spools can be connected to make the column.

It would cost less to simply weld a Tri-Clamp ferrule to the top of your keg rather than spending more money on reducers, gaskets and clamps. It just takes a little time, effort to cut, grind and simply have someone TIG weld the ferrule to it once you've done all the work. After welding, if there's anything that needs ground smooth then I take care of the finish work myself. An angle grinder and a Die Grinder are must have tools in my opinion when it comes to fabrication work for stills.

Also think about how you intend to do stripping runs. You can use your column segments as your pot still riser. There are different ways to do the same thing, but you can use two 90 elbows, your reducer then a product condenser.
You do not have the required permissions to view the files attached to this post.
nick9one1
Novice
Posts: 20
Joined: Mon Apr 13, 2009 11:00 am

Re: which still design for 5gal keg

Post by nick9one1 »

bunny wrote: ↑Thu May 12, 2022 6:55 am Hi!

Is this 5 gal boiler in addition to the 50l you mention here? viewtopic.php?f=85&t=87202

Where have you been and what have you been doing for the last 13 years?

Curious minds want to know. :D
haha sight miscalculation there. 50l = 11 Gallons not 5 :shock:

13 years ago I decided to go down the all grain homebrew route instead of distillation :wink:

Image
nick9one1
Novice
Posts: 20
Joined: Mon Apr 13, 2009 11:00 am

Re: which still design for 5gal keg

Post by nick9one1 »

Salt Must Flow wrote: ↑Thu May 12, 2022 7:31 am It's easy to scale down basic still designs. For a VM, just go with a 2" column, 2" tee, reduce down to a 1" gate valve. Precisely how you do it will likely make very little if not any difference in how it behaves. You will benefit with a taller column.

For instance I went with a short tee so the vapor takeoff wouldn't be unnecessarily long. I made and installed/soldered a copper thermowell into the reducer so I can monitor the vapor takeoff temp.
tri-clamp short tee.png

I went into this hobby knowing I'll likely be doing this for a good number of years so I stepped up to a 3" column rather than a 2". I wasn't going to commit to a 4" because I wasn't confident I'd have multiple 240V circuits at the time and I already had 15.5 gal kegs for boilers. 3" is faster producing than 2" and I'm glad I made it larger. If copper is more expensive then just go with stainless Tri-Clamp spools instead. Multiple spools can be connected to make the column.

It would cost less to simply weld a Tri-Clamp ferrule to the top of your keg rather than spending more money on reducers, gaskets and clamps. It just takes a little time, effort to cut, grind and simply have someone TIG weld the ferrule to it once you've done all the work. After welding, if there's anything that needs ground smooth then I take care of the finish work myself. An angle grinder and a Die Grinder are must have tools in my opinion when it comes to fabrication work for stills.

Also think about how you intend to do stripping runs. You can use your column segments as your pot still riser. There are different ways to do the same thing, but you can use two 90 elbows, your reducer then a product condenser.
Thanks, some interesting points made there.

You're right about the cost of adapters. I hadn't realised how expensive they are for the larger sizes.

A 2.5" to 2" copper reducer is about 25 USD.
A 2.5" Weld On Ferrule is less than 5 USD

I'm fairly adept with my mig welder and have some stainless wire. So there is no reason I couldn't do that.
User avatar
Salt Must Flow
Master of Distillation
Posts: 3151
Joined: Sat Jan 29, 2022 2:06 pm
Location: Wuhan China (Novel Coronavirus Laboratory)

Re: which still design for 5gal keg

Post by Salt Must Flow »

nick9one1 wrote: ↑Thu May 12, 2022 11:20 am
Salt Must Flow wrote: ↑Thu May 12, 2022 7:31 am It's easy to scale down basic still designs. For a VM, just go with a 2" column, 2" tee, reduce down to a 1" gate valve. Precisely how you do it will likely make very little if not any difference in how it behaves. You will benefit with a taller column.

For instance I went with a short tee so the vapor takeoff wouldn't be unnecessarily long. I made and installed/soldered a copper thermowell into the reducer so I can monitor the vapor takeoff temp.
tri-clamp short tee.png

I went into this hobby knowing I'll likely be doing this for a good number of years so I stepped up to a 3" column rather than a 2". I wasn't going to commit to a 4" because I wasn't confident I'd have multiple 240V circuits at the time and I already had 15.5 gal kegs for boilers. 3" is faster producing than 2" and I'm glad I made it larger. If copper is more expensive then just go with stainless Tri-Clamp spools instead. Multiple spools can be connected to make the column.

It would cost less to simply weld a Tri-Clamp ferrule to the top of your keg rather than spending more money on reducers, gaskets and clamps. It just takes a little time, effort to cut, grind and simply have someone TIG weld the ferrule to it once you've done all the work. After welding, if there's anything that needs ground smooth then I take care of the finish work myself. An angle grinder and a Die Grinder are must have tools in my opinion when it comes to fabrication work for stills.

Also think about how you intend to do stripping runs. You can use your column segments as your pot still riser. There are different ways to do the same thing, but you can use two 90 elbows, your reducer then a product condenser.
Thanks, some interesting points made there.

You're right about the cost of adapters. I hadn't realised how expensive they are for the larger sizes.

A 2.5" to 2" copper reducer is about 25 USD.
A 2.5" Weld On Ferrule is less than 5 USD

I'm fairly adept with my mig welder and have some stainless wire. So there is no reason I couldn't do that.
Most here usually go with either 2" or step it up to 3". Nothing wrong with 2.5", but you're almost to 3" and a little bit bigger makes a noticeable difference in output. Also I imagine 2" and 3" parts are more common too. Sure there's a lot of people that have 4" and even 6" stills that go really really fast, but require much more power.
Post Reply