6 inch bubble cap glasser
Moderator: Site Moderator
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
6 inch bubble cap glasser
I need borosilicate Glass tubing 12" long and 6-8" dia.
I've found glass chimneys on amazon that's the size and height I need but the wall thickness is only .090" 2.3mm.
Anybody know of a place to get something thicker?
I've found glass chimneys on amazon that's the size and height I need but the wall thickness is only .090" 2.3mm.
Anybody know of a place to get something thicker?
- Bushman
- Admin
- Posts: 18610
- Joined: Tue Mar 30, 2010 5:29 am
- Location: Pacific Northwest
Re: 6 inch bubble cap glasser
Mash Rookie was a glass blower by trade and made my condensor out of borosilicate glass. I have another friend that is a professional glass blower, I will check with him tomorrow.
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Thanks bushman.
I'm thinking about using 2 bubble plates on a tree with a dimroth dephleg.
The fun part will be making the end caps that sandwich the tubing.
I've got a 1/2" thick chunk of copper that's big enough for the end caps and a lathe.
I'm thinking about using 2 bubble plates on a tree with a dimroth dephleg.
The fun part will be making the end caps that sandwich the tubing.
I've got a 1/2" thick chunk of copper that's big enough for the end caps and a lathe.
You do not have the required permissions to view the files attached to this post.
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Dangit, what I thought was 1/2" is only 1/4"
You do not have the required permissions to view the files attached to this post.
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
How to make the end caps isn't decided yet.
There are a couple options.
1. Use the lathe to cut rings out of the copper plate.
2. Cut a long strip out of the copper, bend it into a ring and weld it.
3. Make a pattern and try to cast the end caps out of scrap copper.
There are a couple options.
1. Use the lathe to cut rings out of the copper plate.
2. Cut a long strip out of the copper, bend it into a ring and weld it.
3. Make a pattern and try to cast the end caps out of scrap copper.
- Copperhead road
- Distiller
- Posts: 2079
- Joined: Thu Jan 12, 2017 4:28 pm
- Location: Brisvegas downunder OZ
Re: 6 inch bubble cap glasser
Don’t think I have ever seen a build thread where they have cast copper before,
That would be pretty cool.
Would that be neater than the lathe option Shady?
That would be pretty cool.
Would that be neater than the lathe option Shady?
Never mistake kindness for weakness....
- Salt Must Flow
- Master of Distillation
- Posts: 3150
- Joined: Sat Jan 29, 2022 2:06 pm
- Location: Wuhan China (Novel Coronavirus Laboratory)
Re: 6 inch bubble cap glasser
What's the budget for this part of the project? Oakstills has a 6" x 12" Tri-Clamp sight glass for $228. Might find a better deal on AliExpress or elsewhere for all I know.
-
NormandieStill
- Distiller
- Posts: 2308
- Joined: Wed Dec 30, 2020 10:17 pm
- Location: Northwest France
Re: 6 inch bubble cap glasser
My guess is that castings will still need finishing on the lathe. But they could be much chunkier than from plate.
That'd be some pretty copper porn right there.
That'd be some pretty copper porn right there.
"I have a potstill that smears like a fresh plowed coon on the highway" - Jimbo
A little spoon feeding *For New & Novice Distillers
A little spoon feeding *For New & Novice Distillers
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
That would be almost cheating. I attempted to order the 6" x 18" sight glass but the order was rejected.Salt Must Flow wrote: ↑Fri Sep 19, 2025 10:14 pm What's the budget for this part of the project? Oakstills has a 6" x 12" Tri-Clamp sight glass for $228. Might find a better deal on AliExpress or elsewhere for all I know.
I'll take that as a sign and build it.
- Copperhead road
- Distiller
- Posts: 2079
- Joined: Thu Jan 12, 2017 4:28 pm
- Location: Brisvegas downunder OZ
Re: 6 inch bubble cap glasser
That is exactly why I thought casting would be awesome to do if possible…NormandieStill wrote: ↑Fri Sep 19, 2025 10:32 pm But they could be much chunkier than from plate.
That'd be some pretty copper porn right there.
Never mistake kindness for weakness....
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Kinda what I was thinking.NormandieStill wrote: ↑Fri Sep 19, 2025 10:32 pm My guess is that castings will still need finishing on the lathe. But they could be much chunkier than from plate.
That'd be some pretty copper porn right there.
Now I need to see if my forge can be used to melt copper.
- Salt Must Flow
- Master of Distillation
- Posts: 3150
- Joined: Sat Jan 29, 2022 2:06 pm
- Location: Wuhan China (Novel Coronavirus Laboratory)
Re: 6 inch bubble cap glasser
I've purchased from Oakstills and from AliExpress without issue and so has many others. As long as you use a major credit card, there's really no risk.shadylane wrote: ↑Fri Sep 19, 2025 10:44 pmThat would be almost cheating. I attempted to order the 6" x 18" sight glass but the order was rejected.Salt Must Flow wrote: ↑Fri Sep 19, 2025 10:14 pm What's the budget for this part of the project? Oakstills has a 6" x 12" Tri-Clamp sight glass for $228. Might find a better deal on AliExpress or elsewhere for all I know.
I'll take that as a sign and build it.![]()
I totally get the whole build it yourself thing and the challenge to not purchase a major part. I agree, it would be cool as hell to be able to smelt some copper, pour, cast and machine it. Then comes sourcing the proper diameter and thickness of the proper glass. It's a ballsy endeavor and that's a fact. These Tri-Clamp sight glasses are truly reliable and built like a tank. Either way you go, I'm sure it will work out and it will be an interesting build.
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Ordering a readymade sight glass from Oakstills would be the logical option and I still might go that way.
First, I'll try building the bottom end cap so there isn't a need of an adapter to the smaller tri--clamp on the boiler.
The top end cap will be interesting since it goes from 6" to 1" and has a dephleg inside it.
I'll be calling oakstill to see if they sell only the glass.
I've done many things successfully but trying to blow glass is beyond my pay grade.
First, I'll try building the bottom end cap so there isn't a need of an adapter to the smaller tri--clamp on the boiler.
The top end cap will be interesting since it goes from 6" to 1" and has a dephleg inside it.
I'll be calling oakstill to see if they sell only the glass.
I've done many things successfully but trying to blow glass is beyond my pay grade.
Last edited by shadylane on Sat Sep 20, 2025 12:59 am, edited 1 time in total.
-
MooseMan
- Master of Distillation
- Posts: 3294
- Joined: Fri May 28, 2021 4:54 am
- Location: Wales UK
Re: 6 inch bubble cap glasser
Oh Shady Pleeeeeeeease make some copper castings!
They can be as rough as you like, then you can spin up a lovely shiny finish on the lathe and get an almost perfect groove fit to the glass.
What an absolutely awesome project that would be, I wish we had a "We are not worthy" emoji on the board.
Edit: Do a search on AliExpress for "Borosilicate glass cylinder" and thank me later!
They can be as rough as you like, then you can spin up a lovely shiny finish on the lathe and get an almost perfect groove fit to the glass.
What an absolutely awesome project that would be, I wish we had a "We are not worthy" emoji on the board.
Edit: Do a search on AliExpress for "Borosilicate glass cylinder" and thank me later!
Make Booze, not War!
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Casting copper fittings is a rabbit hole I haven't dug in yet, I'll keep folks posted on what I find while trying.
Last edited by shadylane on Sun Sep 21, 2025 8:55 pm, edited 2 times in total.
-
30xs
- Rumrunner
- Posts: 675
- Joined: Thu Jan 03, 2019 6:05 pm
- Location: WV
Re: 6 inch bubble cap glasser
I machined a few pieces for my flute on a lathe. Keep some lube handy. I machined the pieces dry and it’s amazing how loud copper can scream.
The imagined image of a copper sight glass is sexy. Since you don’t have the thickness you wanted would a laminated piece work. You could use a 1/4 copper disc on the bottom with a 2 1/8” hole to register a copper stub, a 1/4” stainless disc with an opening the size of the inside of the pipe, then a ring to register your glass on top of it. You could even register your holes through the copper so that the nuts tightened down on stainless only. Not sure how much pressure the thermal expansion from the copper would add to the glass.
The imagined image of a copper sight glass is sexy. Since you don’t have the thickness you wanted would a laminated piece work. You could use a 1/4 copper disc on the bottom with a 2 1/8” hole to register a copper stub, a 1/4” stainless disc with an opening the size of the inside of the pipe, then a ring to register your glass on top of it. You could even register your holes through the copper so that the nuts tightened down on stainless only. Not sure how much pressure the thermal expansion from the copper would add to the glass.
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Looks like my forge doesn't get hot enough.
You do not have the required permissions to view the files attached to this post.
- Copperhead road
- Distiller
- Posts: 2079
- Joined: Thu Jan 12, 2017 4:28 pm
- Location: Brisvegas downunder OZ
Re: 6 inch bubble cap glasser
Shady do you have a “plan B” for the casting?
I hope the does not mean you are aborting the mission…
Never mistake kindness for weakness....
-
Roo
- Posts: 86
- Joined: Sun May 18, 2025 12:59 am
- Location: Melboure(ish), Australia
Re: 6 inch bubble cap glasser
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
Plan B is I just ordered a new forge.Copperhead road wrote: ↑Sat Sep 20, 2025 4:31 pm
Shady do you have a “plan B” for the casting?
I hope the does not mean you are aborting the mission…
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
That's it.Roo wrote: ↑Sat Sep 20, 2025 5:20 pm
Is this what you are looking for?
https://oakstills.com/en-au/products/re ... ight-glass
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
I thought about making DIY green sand but instead ordered petrobond casting sand.
It chafes my ass to spend $3 a pound for a mixture of 70% sand and 30% clay.
Tomorrow I'll make the bottom pattern and boxes "cope and drag" out of wood.
It chafes my ass to spend $3 a pound for a mixture of 70% sand and 30% clay.
Tomorrow I'll make the bottom pattern and boxes "cope and drag" out of wood.
- Yummyrum
- Admin
- Posts: 10563
- Joined: Sat Jul 06, 2013 2:23 am
- Location: Fraser Coast QLD Aussie
Re: 6 inch bubble cap glasser
Now I’m excited Shadyshadylane wrote: ↑Sat Sep 20, 2025 5:49 pmPlan B is I just ordered a new forge.Copperhead road wrote: ↑Sat Sep 20, 2025 4:31 pm
Shady do you have a “plan B” for the casting?
I hope the does not mean you are aborting the mission…
My recommended goto .
https://homedistiller.org/wiki/index.ph ... ion_Theory
https://homedistiller.org/wiki/index.ph ... ion_Theory
- Copperhead road
- Distiller
- Posts: 2079
- Joined: Thu Jan 12, 2017 4:28 pm
- Location: Brisvegas downunder OZ
Re: 6 inch bubble cap glasser
Shady what kind of forge did you end up ordering ?
Never mistake kindness for weakness....
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
"VEVOR Propane Melting Furnace Kit 8KG"
I wanted bang for the buck, Amazone $109 plus tax looked like a good fast option.
I wanted bang for the buck, Amazone $109 plus tax looked like a good fast option.
-
MooseMan
- Master of Distillation
- Posts: 3294
- Joined: Fri May 28, 2021 4:54 am
- Location: Wales UK
Re: 6 inch bubble cap glasser
Me too!
There's no rules that say you can't do a build thread, on a bit of kit that is going to make a still part, right Yummy?
Make Booze, not War!
- Yummyrum
- Admin
- Posts: 10563
- Joined: Sat Jul 06, 2013 2:23 am
- Location: Fraser Coast QLD Aussie
Re: 6 inch bubble cap glasser
Damn right 
My recommended goto .
https://homedistiller.org/wiki/index.ph ... ion_Theory
https://homedistiller.org/wiki/index.ph ... ion_Theory
- shadylane
- Master of Distillation
- Posts: 12863
- Joined: Sat Oct 27, 2007 11:54 pm
- Location: Hiding In the Boiler room of the Insane asylum
Re: 6 inch bubble cap glasser
I stacked and glued several pieces of plywood to make the form out of.
A 1/2" bolt is being used to hold the layers together until the glue dries.
See the round end piece on the right, there's supposed to be a matching piece on the left.
I haven't a clue where it ran off to, so I clamped the pieces together and maybe I'll find it tomorrow, If not I'll make another.
Tomorrow should be easier, today I had to battle red wasps over who owned the lathe.
I used a spray bottle with soapy water to suffocate them and called Bubba.
There was a big nest, and he thinks wasp larva is the secret ingredient for fishing.
A 1/2" bolt is being used to hold the layers together until the glue dries.
See the round end piece on the right, there's supposed to be a matching piece on the left.
I haven't a clue where it ran off to, so I clamped the pieces together and maybe I'll find it tomorrow, If not I'll make another.
Tomorrow should be easier, today I had to battle red wasps over who owned the lathe.
I used a spray bottle with soapy water to suffocate them and called Bubba.
There was a big nest, and he thinks wasp larva is the secret ingredient for fishing.
You do not have the required permissions to view the files attached to this post.
-
MooseMan
- Master of Distillation
- Posts: 3294
- Joined: Fri May 28, 2021 4:54 am
- Location: Wales UK
Re: 6 inch bubble cap glasser
Off to a good start!
Are you going to try casting a section to turn a Tri clamp flange on one of the end plates?
Or just cast them both the same and add that later?
Bubba is right about the larva, but it's not usually worth the pain! Haha
Are you going to try casting a section to turn a Tri clamp flange on one of the end plates?
Or just cast them both the same and add that later?
Bubba is right about the larva, but it's not usually worth the pain! Haha
Make Booze, not War!
- PalCabral
- Posts: 2764
- Joined: Tue Oct 29, 2024 4:02 am
- Location: Stockholm, Sweden
Re: 6 inch bubble cap glasser
Bubba should get an account in HD and join us. It feels like he's here all the time anyway. 