Alcoengine Reflux Column

Vapor, Liquid or Cooling Management. Flutes, plates, etc.

Moderator: Site Moderator

nikolav
Novice
Posts: 72
Joined: Mon Sep 16, 2024 6:38 pm
Location: Auckland, New Zealand

Re: Alcoengine Reflux Column

Post by nikolav »

SW_Shiner wrote: ↑Tue Oct 21, 2025 5:54 pm
decoy wrote: ↑Tue Oct 21, 2025 5:14 pm Try running the still with no condenser, see how much vapour comes out the top.
I'd be careful recommending people run without a condenser.

Throw a litre or two of water in the boiler and see how much steam makes it through.

Another thing would be to 'tease' some of the SS mesh that is in the coil. Pull it down a little so it makes contact with the pointy bit, if you get what i mean. Kinda fill up that empty space and it might help direct more reflux down the collector.
Sorry, mate, I missed that
Do you mean like that?
I'll give it a try.
Image
capture photo and upload
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: Alcoengine Reflux Column

Post by Yummyrum »

You can calculate power by how long it takes to bring x amount of water that starts at y degrees, to the boil .

Sw_Shiner mentioned coolant flow early on .
I guess it is possible that if you have an excessive amount of very cold water flowing through the condenser that it will sub cool the top of the still meaning that the still might behave more like a CCVM ,where the vapour is condensing a lot lower down in the column than it should be . Meaning not a lot of vapour makes it up to the actual coil to be collected by the cup .

But heck , it would have to be very cold water . But then again , in combination with maybe lower than optimum boiler power ,it might be a thing . God , really clutching at straws here .
And on that note , have you tried reversing the coolant in/out lines ? It’s a double wound coil but it might make a difference if your water is really cold . Also , the exit water temp should be quite warm . I’m not sure I agree with it being 30°C .
nikolav
Novice
Posts: 72
Joined: Mon Sep 16, 2024 6:38 pm
Location: Auckland, New Zealand

Re: Alcoengine Reflux Column

Post by nikolav »

I've never measured how long it takes to bring a wash to boil, but I would say about an hour +/- 10 minutes.
Regarding switching the inlet/outlet, maybe I did it, but intentionally. I don't think it was ever mentioned in the manual if that mattered. Will look into it.
The water I use is either tap water, which is 20-22 degrees C or tank water which now is also around there.
The manual only states about minimum flow rate of 8l/m max tem of 35 C for the cooling water.
I don't see how too cold and/too much could be a problem.
I.e. I can't see how the vapor would condense below the coil. When I touch the still it is cold probably at top 5 cm and at 10-15 cm down, I can't touch it anymore.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: Alcoengine Reflux Column

Post by SW_Shiner »

Cooling the reflux too much can cause it to lower the temp of the top of the packing. If the distillate at the top gets too cold and cant vaporize at the right rate, then it ends up falling lower in the column, instead of re-boiling and continuing up to the reflux condenser and collection. Also, if you can feel cold, vapour will condense there. Copper conducts heat very well as we know, so the cold portion of the still you feel, could very well be extending past the bottom of the coil. It may not be by much, but it could be enough to cause issues.

Edit: It doesn't need to be cold to the touch, it just has to be cold enough to condense the vapour.
User avatar
Saltbush Bill
Global moderator
Posts: 11649
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: Alcoengine Reflux Column

Post by Saltbush Bill »

Water leaving your reflux condencer can be quite warm.to the touch. Quite warm almost bath tub hot.
nikolav
Novice
Posts: 72
Joined: Mon Sep 16, 2024 6:38 pm
Location: Auckland, New Zealand

Re: Alcoengine Reflux Column

Post by nikolav »

Just had another run.
Some more observations.
The water flow from the tap is much more than 8l/h. But once I connect it to the coil it drops to a maximum of ~5l/h.
Maybe that's normal, I don't know.
The exiting water is just a little bit warmer than the incoming water. The difference is very negligible.
Adjusting the cooling water doesn't change anything.
I ran it again through a voltage regulator. When I go down to about 50% the dripping almost stops. The higher the voltage, the greater output rate, but not by much.
The alcohol comes out very hot - around 45-50 degrees Celsius.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: Alcoengine Reflux Column

Post by SW_Shiner »

That sounds like too much water flow, its better if its hot. Hot enough that you can stick your finger under, but not for long.

The distillate will be hot, that's just how LM stills are. Once its condensed it just falls into the collection area, and gets reheated by the surrounding hot vapour. I think most people now that make an LM also make a small liebig to act as a product cooler to cool the distillate after it leaves the still. I did as it makes checking the proof during the run faster.
nikolav
Novice
Posts: 72
Joined: Mon Sep 16, 2024 6:38 pm
Location: Auckland, New Zealand

Re: Alcoengine Reflux Column

Post by nikolav »

Case closed, team. It's time a new boiler...
Just tried my mate's boiler. Also T500, but newer model.



200 ml in about 12 minutes. Pretty damn close to the advertised 1200 ml in 60 minutes.

Thanks everyone the help, guys!

PS. Apparently my boiler is still fully sufficient for the T500 reflux, but not for the Alcoengine.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: Alcoengine Reflux Column

Post by SW_Shiner »

Oh nice. Glad you manage to work out the issue.
User avatar
Saltbush Bill
Global moderator
Posts: 11649
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: Alcoengine Reflux Column

Post by Saltbush Bill »

Glad thats sorted.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: Alcoengine Reflux Column

Post by Yummyrum »

Glad you got the speed up.

Not convinced that a few watts extra power fixed the problem …. but what ever .

I’m still thinking the extra power just masked over cooling upstairs .
User avatar
Saltbush Bill
Global moderator
Posts: 11649
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: Alcoengine Reflux Column

Post by Saltbush Bill »

I think it was not enough power right from the start.
That's why I said try another boiler on page one.
Not enough vapour reaching the RC nothings going to come out the spout.
Crook element in first boiler.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: Alcoengine Reflux Column

Post by Yummyrum »

But enough heat to bring a wash to the boil in an hour . ?

Seems strange folk can run a 2” boka of other reflux still on 2kw but they can turn it down to 1200watts or so to take off foreshots and they still have plenty of reflux to be pulling fores off at 95% yet this OP can’t even even collect more than a few drops condensing off the coil in his cup to get a few drops . Like what power is his element ? 500w or less ?

It makes no sense . How can his wash get to the boil in an hour ? Unless he is only putting 5 litres in the boiler or something .
User avatar
Saltbush Bill
Global moderator
Posts: 11649
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: Alcoengine Reflux Column

Post by Saltbush Bill »

But was the wash ever at a full boil or was it just a very gentle simmer, or sounded like it was boiling. Maybe the OP mentioned that part and I missed it?
My thought was that somehow the element wasn't operating at full power.
My T500 boiler did weird things once, got hot but took twice as long as normal.
I found a loose wire under the plate at the bottom, problem fixed.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: Alcoengine Reflux Column

Post by SW_Shiner »

Yummyrum wrote: ↑Fri Oct 24, 2025 1:07 pm But enough heat to bring a wash to the boil in an hour . ?

Seems strange folk can run a 2” boka of other reflux still on 2kw but they can turn it down to 1200watts or so to take off foreshots and they still have plenty of reflux to be pulling fores off at 95% yet this OP can’t even even collect more than a few drops condensing off the coil in his cup to get a few drops . Like what power is his element ? 500w or less ?

It makes no sense . How can his wash get to the boil in an hour ? Unless he is only putting 5 litres in the boiler or something .
A boka collects 100% of the reflux before over flowing and continuing down the packing. The alcoengine only ever collects a portion of the reflux, unless every single drop travels down the little spike and makes it to the cup. He was most likely getting sufficient reflux to run the still, were it designed better. My guess as to why this happened this way, would be that there was not enough vapour being produced to compensate for the collection inefficiency.

I was convinced from the start it was a power issue as that made the most sense and fit in with the issues he was having. But i also think the less than ideal design of the still head was also a factor.

Also I'm going have to look more into turning the power down for fore shots. I'm not familiar with that as a practice for LM stills and I've never done it.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: Alcoengine Reflux Column

Post by SW_Shiner »

Saltbush Bill wrote: ↑Fri Oct 24, 2025 1:31 pm But was the wash ever at a full boil or was it just a very gentle simmer, or sounded like it was boiling. Maybe the OP mentioned that part and I missed it?
My thought was that somehow the element wasn't operating at full power.
My T500 boiler did weird things once, got hot but took twice as long as normal.
I found a loose wire under the plate at the bottom, problem fixed.
He did mention it taking approx 1 hour to boil.
He said he had a Gen 1 boiler, maybe i should have checked, but i assumed he meant it was the same as the Gen 1 i have. Which has an 1850w exposed element. I haven't measured how much it uses now as i lost the power cord.
User avatar
Saltbush Bill
Global moderator
Posts: 11649
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: Alcoengine Reflux Column

Post by Saltbush Bill »

Long time since ive looked at mine to see exactly but from memory its 2200w
Over the years they have changed.
Ive never seen a T500 boiler with an exposed element.
nikolav
Novice
Posts: 72
Joined: Mon Sep 16, 2024 6:38 pm
Location: Auckland, New Zealand

Re: Alcoengine Reflux Column

Post by nikolav »

No idea what the wattage of my boiler is, but the element is not exposed. All I know, it's very old. It's second hand, and it came with the ceramic saddles. Also, it comes with two temp probes. One at the top and one at the water exit.

Anyway, just got a new boiler - the Kegland's 35l. I also got the digimash upgrade, so I will also replace my chilly bin DIY mash tun. The fun part is that out of the box, the boiler is not exactly compatible with my existing lids - it's too loose. Replacement clamps ordered as well, just need to wait for them. As I type that, I'm also 3D printing some (high temp) shims for the clamps so I can at least try it before the new clamps arrive.
Post Reply