6 inch bubble cap glasser

Vapor, Liquid or Cooling Management. Flutes, plates, etc.

Moderator: Site Moderator

Post Reply
User avatar
Corn Cracker
Posts: 1397
Joined: Sun Jun 13, 2021 7:25 am
Location: s.e. Texas

Re: 6 inch bubble cap glasser

Post by Corn Cracker »

Ain't nothin but a step for a stepper like you, Shady
I think I'll go home and fire up my still, it might not make me feel better but, I bet it will
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Here's the top plate downcomer with a reflux spreader.
After pounded waves into the ring, I discovered it was now smaller in ID and wouldn't fit so filing was needed. :roll:
You do not have the required permissions to view the files attached to this post.
User avatar
jonnys_spirit
Master of Distillation
Posts: 4174
Joined: Wed Oct 21, 2015 7:58 am
Location: The Milky Way

Re: 6 inch bubble cap glasser

Post by jonnys_spirit »

It just might be a rumbrella

Very cool project Shady !

Cheers,
jonny
————
i prefer my mash shaken, not stirred
————
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Rumbrella, that's what I was going to call the piece that spreads the reflux from the defleg over the top plate.
But I'm getting ahead of myself on that part of the build because it might not be needed. :wink:
If everything goes according to plan, the dephleg will drip reflux all over the top plate.
User avatar
Copperhead road
Distiller
Posts: 2111
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 6 inch bubble cap glasser

Post by Copperhead road »

Shady did you end up getting the correct Seals for leak test?
Considering you started out with a furnace and a pile of scrap copper it’s all really starting to take shape and come together resulting in a very cool unique 6” glasser build.
Never mistake kindness for weakness....
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Copperhead road wrote: ↑Thu Oct 30, 2025 5:07 pm Shady did you end up getting the correct Seals for leak test?
Considering you started out with a furnace and a pile of scrap copper it’s all really starting to take shape and come together resulting in a very cool unique 6” glasser build.
I searched for PTFE seals that had a silicone core but couldn't find any, so I bought a sheet of 1/8" food grade silicone and several rolls of PTFE tape.
Once I finish building all the copper parts, I'll cut the silicone sheet into rings and wrap it with several layers of PTFE tape.
30xs
Rumrunner
Posts: 686
Joined: Thu Jan 03, 2019 6:05 pm
Location: WV

Re: 6 inch bubble cap glasser

Post by 30xs »

https://ebay.us/m/EhS0Rr

Something like this would allow you to machine out a couple grooved gaskets. I made a mandrel to cut flat copper discs with no holes I can try to get a picture of. A little expensive but could be done from solid PTFE.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

I think solid PTFE is going to be too hard and not conform, That's the reason for silicone and PTFE tape.
Almost done with the plates, all they need is string wrapped around them for glass to plate seal.
Depending on how tight the plates fit in the glass a rod might be needed to hang the plates from.
If a tree bolt is needed, a 1/4" hole will be drilled in the bottom of the downcomer cups.
You do not have the required permissions to view the files attached to this post.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: 6 inch bubble cap glasser

Post by Yummyrum »

Sounds like a good option to me Shady . :thumbup:
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Making the gaskets that go between the glass and end caps.
I'm not very proud of this one but there's enough material to make several and I'll pick between the lot and use the best 2.
Maybe with practice I'll get better at making them.
On a side note, trying to grind off imperfections from poor cutting doesn't work worth a shit on silicone. :lol:
You do not have the required permissions to view the files attached to this post.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: 6 inch bubble cap glasser

Post by Yummyrum »

I’ve found the easiest way to deal with it is to put a round thing on it of the correct size and cut around it with a very shape Stanley knife .
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

I'm thinking of a cutting tool made from a razor blade glued to stick of wood with 2 holes that can be used for a pivot point to center first the OD and then the ID of the cuts. Might work, might not. Here's a drawing to give folks an idea of what's in my abbynormal brain. :lol
You do not have the required permissions to view the files attached to this post.
User avatar
Steve Broady
Distiller
Posts: 1572
Joined: Thu Aug 25, 2022 9:52 am
Location: NC Piedmont

Re: 6 inch bubble cap glasser

Post by Steve Broady »

IMG_9135.jpeg
I’ve started using this stuff for gaskets, especially for sight glasses. It’s some form of magical PTFE tape that you can shape almost like putty. I have no idea what the adhesive is, but I figured it is only there to hold the tape in place until it gets properly squished. Anything that might be exposed afterwards should be completely dissolved in the cleaning run, and in any case it’s got to be better than a silicone gasket in high proof spirits.
IMG_9127.jpeg
Here I’m using it at both ends of both glass cylinders, so four layers in total. Properly applied, it seals perfectly in my experience.
You do not have the required permissions to view the files attached to this post.
Too much of anything is bad, but too much good whiskey is barely enough. - Mark Twain
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Steve Broady wrote: ↑Sat Nov 01, 2025 6:34 pm IMG_9135.jpeg
I’ve started using this stuff for gaskets, especially for sight glasses. It’s some form of magical PTFE tape that you can shape almost like putty. I have no idea what the adhesive is, but I figured it is only there to hold the tape in place until it gets properly squished. Anything that might be exposed afterwards should be completely dissolved in the cleaning run, and in any case it’s got to be better than a silicone gasket in high proof spirits.
IMG_9127.jpeg
Here I’m using it at both ends of both glass cylinders, so four layers in total. Properly applied, it seals perfectly in my experience.
" It’s some form of magical PTFE tape that you can shape almost like putty"

I don't know what' you're using, but PTFE isn't noted to be squishy.
For now, I'll use silicon for squishyness and wrap it with PTFE tape because it's inert to hot alcohol vapor and other byproducts of fermentation.
Last edited by shadylane on Sat Nov 01, 2025 7:38 pm, edited 1 time in total.
SW_Shiner
Distiller
Posts: 1002
Joined: Wed Feb 07, 2024 3:46 pm
Location: South Waikato, New Zealand

Re: 6 inch bubble cap glasser

Post by SW_Shiner »

shadylane wrote: ↑Sat Nov 01, 2025 4:20 pm I'm thinking of a cutting tool made from a razor blade glued to stick of wood with 2 holes that can be used for a pivot point to center first the OD and then the ID of the cuts. Might work, might not. Here's a drawing to give folks an idea of what's in my abbynormal brain. :lol
I think that should work pretty good. I have a similar tool that I used to cut out the centre of gaskets for pump housings.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

SW_Shiner wrote: ↑Sat Nov 01, 2025 7:36 pm
I think that should work pretty good. I have a similar tool that I used to cut out the centre of gaskets for pump housings.
I've got something similar that's made for cutting circles.
Unfortunately it will probably take longer to find than it will to make one. :lol:
User avatar
Steve Broady
Distiller
Posts: 1572
Joined: Thu Aug 25, 2022 9:52 am
Location: NC Piedmont

Re: 6 inch bubble cap glasser

Post by Steve Broady »

shadylane wrote: ↑Sat Nov 01, 2025 7:35 pm
" It’s some form of magical PTFE tape that you can shape almost like putty"

I don't know what' you're using, but PTFE isn't noted to be squishy.
For now, I'll use silicon for squishyness and wrap it with PTFE tape because it's inert to hot alcohol vapor and other byproducts of fermentation.
It’s sold as “Expanded PTFE Tape.” https://a.co/d/0T3YlLb
As you said, PTFE isn’t known for being soft which gave me some reservations early on, but I will say that this stuff looks and feels and behaves a lot like a somewhat foamy version of the standard plumbing tape. And all that I have used in and around stills remains completely unchanged aside from occasional surface grunge. It sure seems like it’s inert, as PTFE should be.

I’m certainly not going to advocate for the stuff or trek another what they should be using, but I thought it might be helpful to share it. I learned about it here on HD some time ago, and it’s worked quite well for me.
Too much of anything is bad, but too much good whiskey is barely enough. - Mark Twain
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

End gaskets are done, next is to wrap the plates with string.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Damit man, nothing to show today other than I cut all 6 tie bolts too short.
Now I have to wait for amazon to bring some more. :roll:
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: 6 inch bubble cap glasser

Post by Yummyrum »

shadylane wrote: ↑Mon Nov 03, 2025 3:23 pm Damit man, nothing to show today other than I cut all 6 tie bolts too short.
Now I have to wait for amazon to bring some more. :roll:
That's a shame .I was hoping you were going to wrap the string . I'm wondering how you hold it in place so it doesn't slide off the plate rims when you slide it in the glass ?
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

I'll do the string trick the same way I did it on this 4" glass build.

viewtopic.php?t=78254
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

The inner diameter of glass is notoriously imperfect and trying to get a usable seal can be difficult.
Here's a crude drawing of the workaround I've been using.
The plate OD is intentionally ground to be loose in the glass tube.
A ring is soldered to the plate and shaped to hold the cotton string from slipping off the ring.
You do not have the required permissions to view the files attached to this post.
decoy
Trainee
Posts: 772
Joined: Fri Jan 06, 2006 4:21 pm

Re: 6 inch bubble cap glasser

Post by decoy »

I used copper braid, hope this helps.
Screenshot 2025-11-04 162449.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

I haven't thought about copper braid, there's definitely possibility's especially on a sieve plate build.
The first thing that comes to mind is me getting ham fisted with soldering on the braid and it becoming solid. :lol:
I'll have to give it a try but not right now since I've already headed down this path.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: 6 inch bubble cap glasser

Post by Yummyrum »

Shady , I saw on your 4” that you tried the ring as shown above and also below the plate . Whats your opinion on that now ?

Sorry for all the questions , I just remembered the string thing yiu did and it’s stuck with me as a good idea . I need ti make plates fir my stripper and hoped to try this as a slide in .
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

It worked very well.
Almost zero reflux got past the string seal to drain down and what vapor tried to sneak past the seal had to bubble up through the liquid.
It made the sieve plate easier to load with the seal than without it.
In hindsight, having that good of a seal was almost wasted on a sieve plate were weepage and bubbling are natural part of the plate action.
I'm thinking on a 6" bubble cap plate having a good seal is important considering the 18" circumference.
That and I want to be able to run the caps super slow if I want and weepage would limit that ability.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Yummyrum wrote: ↑Mon Nov 03, 2025 9:43 pm Shady , I saw on your 4” that you tried the ring as shown above and also below the plate . Whats your opinion on that now ?

Sorry for all the questions , I just remembered the string thing yiu did and it’s stuck with me as a good idea . I need ti make plates fir my stripper and hoped to try this as a slide in .
This was the worst design.
It held reflux on the plate but let vapor sneek past without mixing with the liquid causing smearing.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

Here's what happens with no seal, the weepage was excessive and the plate needed lots of power to overcome it.
But there was vapor/reflux interaction.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 6 inch bubble cap glasser

Post by shadylane »

It's easier to have the ring centered the plate so it can be bent to hold the string from slipping.
You do not have the required permissions to view the files attached to this post.
User avatar
Chauncey
Distiller
Posts: 1654
Joined: Sat Feb 06, 2016 1:30 am
Location: NOLA

Re: 6 inch bubble cap glasser

Post by Chauncey »

excellent thread shady
<no stopping to corner anytime [] no parking passenger zone>

When people tell me I'll regret that in the morning, I sleep till noon.
Post Reply