Fixed Valve Plate

Vapor, Liquid or Cooling Management. Flutes, plates, etc.

Moderator: Site Moderator

User avatar
Tammuz
Rumrunner
Posts: 671
Joined: Sat Sep 21, 2024 11:59 am

Re: Fixed Valve Plate

Post by Tammuz »

What about making a sieve plate with 8-9% opening. Then take a thin sieve plate with 6-7% opening and just place that on top so that it floats on top of the bottom plate.
Igitur qui desiderat pacem, praeparet bellum or party till the cows come home!
User avatar
Tammuz
Rumrunner
Posts: 671
Joined: Sat Sep 21, 2024 11:59 am

Re: Fixed Valve Plate

Post by Tammuz »

Duplicate post
Last edited by Tammuz on Sat Feb 15, 2025 9:47 am, edited 1 time in total.
Igitur qui desiderat pacem, praeparet bellum or party till the cows come home!
User avatar
subbrew
Distiller
Posts: 1970
Joined: Thu Jan 21, 2021 1:40 pm
Location: West of the Mississippi

Re: Fixed Valve Plate

Post by subbrew »

For the valves I think copper rivets would work. You could slightly bell the bottom so they did not pop clear out. I don't know what sort of weight they would need to operate efficiently.
User avatar
Tammuz
Rumrunner
Posts: 671
Joined: Sat Sep 21, 2024 11:59 am

Re: Fixed Valve Plate

Post by Tammuz »

Maybe stainless steel rivets would work better. We tried copper with different amount of slack by using different hole sizes. Running rum on spirit runs by the third run they were sticking. Maybe a different designed rivet with a larger head would have worked.
Igitur qui desiderat pacem, praeparet bellum or party till the cows come home!
User avatar
acfixer69
Global moderator
Posts: 5305
Joined: Mon Dec 20, 2010 3:34 pm
Location: CT USA

Re: Fixed Valve Plate

Post by acfixer69 »

I made these 10 or so years ago
CIMG1432.JPG
They worked fine, I only used them for spirit run and they had a great turn down rate.

They are not a fixed valve plate,but I'm not sure what a fixed valve is.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: Fixed Valve Plate

Post by shadylane »

Have multiple long slits in the plate and have soldered on Z strips to direct the vapor blowing into the reflux.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: Fixed Valve Plate

Post by shadylane »

Since the post has drifted a little from fixed plates. Here's a valved plate I did awhile back.
It needed several more valves and more open area to work faster or have lots of extra small perf holes between the valves.
It would start and load just like a well designed bubble cap plate.
Turn on the power and reflux water and the plates would load top to bottom as you watched with no drama.
You do not have the required permissions to view the files attached to this post.
Last edited by shadylane on Fri Feb 14, 2025 6:54 pm, edited 2 times in total.
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: Fixed Valve Plate

Post by Yummyrum »

LWTCS wrote: ↑Tue Feb 11, 2025 1:22 pm
Well so far its about plates that have more operating range than the basic perf plate without the added complexity of a bubble cap plate.
So would I be right in assuming that the turndown of a fixed valve plate can only be as good as a perf plate assuming both have the same open area . (IE with the same open area , both need the same minimum power to hold liquid )

Therefore , increasing operating range can only be done at the turn up end . And this is the idea of shooting the vapour sideways into the liquid rather than straight up .
User avatar
Yummyrum
Admin
Posts: 10579
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: Fixed Valve Plate

Post by Yummyrum »

shadylane wrote: ↑Fri Feb 14, 2025 6:25 pm Have multiple long slits in the plate and have soldered on Z strips to direct the vapor blowing into the reflux.
That would be fairly easy to do Shady . Cut slots with a cutoff disk . Z strips easy to bend . Wouldn’t need to be thick copper .
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: Fixed Valve Plate

Post by shadylane »

Yummyrum wrote: ↑Fri Feb 14, 2025 6:52 pm
So would I be right in assuming that the turndown of a fixed valve plate can only be as good as a perf plate assuming both have the same open area . (IE with the same open area , both need the same minimum power to hold liquid )

Therefore , increasing operating range can only be done at the turn up end . And this is the idea of shooting the vapour sideways into the liquid rather than straight up .
Entrainment would be less of a problem.
I think due to the vapor being blown sideways, the reflux can't drain down the sieve holes as easily.
Therefor a wider range of operation would be possible.
Long story short it would be somewhere in between a bubble cap and sieve plate.
User avatar
shadylane
Master of Distillation
Posts: 12879
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: Fixed Valve Plate

Post by shadylane »

Yummyrum wrote: ↑Fri Feb 14, 2025 6:56 pm
shadylane wrote: ↑Fri Feb 14, 2025 6:25 pm Have multiple long slits in the plate and have soldered on Z strips to direct the vapor blowing into the reflux.
That would be fairly easy to do Shady . Cut slots with a cutoff disk . Z strips easy to bend . Wouldn’t need to be thick copper .
I haven't tried it yet but it looks good in theory. :lol:
User avatar
Swedish Pride
Master of Distillation
Posts: 2870
Joined: Tue Aug 26, 2014 2:16 am
Location: Emerald Isle

Re: Fixed Valve Plate

Post by Swedish Pride »

shadylane wrote: ↑Fri Feb 14, 2025 7:07 pm
Yummyrum wrote: ↑Fri Feb 14, 2025 6:56 pm
shadylane wrote: ↑Fri Feb 14, 2025 6:25 pm Have multiple long slits in the plate and have soldered on Z strips to direct the vapor blowing into the reflux.
That would be fairly easy to do Shady . Cut slots with a cutoff disk . Z strips easy to bend . Wouldn’t need to be thick copper .
I haven't tried it yet but it looks good in theory. :lol:
Sure does, can't beat a visual representation.

Looks less hassle than drilling a godscillion holes in a plate.
Cheaper too, the way I snapped drill bits anyway
Don't be a dick
googe
retired
Posts: 3914
Joined: Wed Jun 20, 2012 6:53 pm
Location: awwstralian in new zealund

Re: Fixed Valve Plate

Post by googe »

Cool subject LWTCS, I like zacks pic. No moving parts. So, are you after a plate that has the action of perfs and bubble and valve? I see no issues with no downcomer if you have flow right, would only take a bit of Science which is abundant here. I did it easy with the flap plate and I'm dumb as shit lol
Here's to alcohol, the cause of, and solution to, all life's problems.
"Homer J Simpson"
googe
retired
Posts: 3914
Joined: Wed Jun 20, 2012 6:53 pm
Location: awwstralian in new zealund

Re: Fixed Valve Plate

Post by googe »

Bump....
Here's to alcohol, the cause of, and solution to, all life's problems.
"Homer J Simpson"
Post Reply