8" plates

Vapor, Liquid or Cooling Management. Flutes, plates, etc.

Moderator: Site Moderator

Post Reply
30xs
Rumrunner
Posts: 683
Joined: Thu Jan 03, 2019 6:05 pm
Location: WV

Re: 8" plates

Post by 30xs »

A scroll saw would make short work of the plate slots. Building the box like Fzb said would be a piece of cake. Pushing the envelope I think I would go for the gusto and do rectangle.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Here's a couple of the caps that I'm going to braze together.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Here's the finished caps after brazing.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

All the caps are made and the holes drilled in the plates for them.
I'm waiting until the downcomers are done and the hole cut for them before starting to solder everything together.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Here's the cap dimensions.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

I made the downcomers out of 1" ID tubing, they haven't been cut to length yet.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Here's the downcomer dimensions.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Plates soldered together.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Next on the list is to redo the TIG welds connecting the ferules to the copper.
I should have done that earlier but didn't get around to it.
You do not have the required permissions to view the files attached to this post.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Finished re-welding the ferules and it looks like shit. But the welds are in the inside and no-one will see them. :lol:
One of the seals on the window is missing so I need to fix that and then I could put everything together and do a leak check.
User avatar
Copperhead road
Distiller
Posts: 2090
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 8" plates

Post by Copperhead road »

It’s looking killer Shady….

Can’t wait to see that behemoth running. :shifty:
Never mistake kindness for weakness....
googe
retired
Posts: 3914
Joined: Wed Jun 20, 2012 6:53 pm
Location: awwstralian in new zealund

Re: 8" plates

Post by googe »

Looking good shady, like the angle on the downcomers, any extra flow is a bonus.
Here's to alcohol, the cause of, and solution to, all life's problems.
"Homer J Simpson"
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

I capped off the bottom of the column and filled it with water to see if there's any leaks and there is.
So instead of fixing them, I decided to put it on the boiler and take a pic.
Maybe tommarrrow I get motivated and do some more work. :lol:
You do not have the required permissions to view the files attached to this post.
User avatar
Copperhead road
Distiller
Posts: 2090
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 8" plates

Post by Copperhead road »

I like the angle of your site glasses also like googe mentioned, much easier to see what’s happening on your plates.

You’re definitely innovating with leaps and bounds for Home hobby distillers….. :clap:
Never mistake kindness for weakness....
User avatar
Saltbush Bill
Global moderator
Posts: 11648
Joined: Thu Mar 17, 2011 2:13 am
Location: Northern NSW Australia

Re: 8" plates

Post by Saltbush Bill »

I think it needs a couple more sections for experiments.
Otherwise it looks the bees knees.
That seats getting dusty, time for a ride.
User avatar
Yummyrum
Admin
Posts: 10569
Joined: Sat Jul 06, 2013 2:23 am
Location: Fraser Coast QLD Aussie

Re: 8" plates

Post by Yummyrum »

Actually , that boiler looks undersized now .

….wait :shh:

Just get on and run the damn thing :ebiggrin:
User avatar
BigSwede
Distiller
Posts: 1000
Joined: Thu Feb 06, 2014 10:36 am

Re: 8" plates

Post by BigSwede »

Shady, that is art. Leaks always seem to pop up in a big, complicated build. Hopefully it's just a gasket rather than a weld or solder joint.

Thank you for all the great details and pictures! :clap:
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

BigSwede wrote: ↑Fri May 29, 2026 7:40 am Shady, that is art. Leaks always seem to pop up in a big, complicated build. Hopefully it's just a gasket rather than a weld or solder joint.
Zero leaks on the plate and triclamp seals.
It's a couple pin holes on the ferule to copper that's busting my balls. Once upon a time I could weld better. :lol:
User avatar
Copperhead road
Distiller
Posts: 2090
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 8" plates

Post by Copperhead road »

:egeek: When it comes to stills I’m a buyer and not a builder, but what you have achieved shady is Mickey Mouse!

I love your work…… Mr Shady
Never mistake kindness for weakness....
30xs
Rumrunner
Posts: 683
Joined: Thu Jan 03, 2019 6:05 pm
Location: WV

Re: 8" plates

Post by 30xs »

I’d just smooth out a little of the the ugly that bothers you and just use some stay brite and Harris 8 to fill in the leaks. The structural shouldn’t be an issue with a mostly welded construction. Just my two cents.

I will say it is a thing of beauty as it sets. Top notch work as always.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

I'll get the job done, just not as good or fast as I once could. :lol:

The extra space between the plates is to limit entrainment. I almost used 12" because that was the size of the copper sheet.
But decided 9" would work as good and be less ugly. Plus I had a need for a couple 3" x 24" strips.

Most of the plate builds I've seen have only 4 - 6" of plate spacing, but I think there's an advantage to have extra distance to allow more time for droplets to fall back to the plate and not get carried up with vapor to the next plate.
Using a 4" glasser that had the plates on a tree, I did some experiments using different plate spacing and found more is better.
User avatar
Copperhead road
Distiller
Posts: 2090
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 8" plates

Post by Copperhead road »

I decided to give this thread a bump.

How is the 8incher going Shady ?
I get enjoyment out of your wild unique builds.... :?:
Never mistake kindness for weakness....
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

Everything is done and ready to go, but me.
OtisT
Master of Distillation
Posts: 3411
Joined: Sat Oct 24, 2015 11:59 am
Location: Hawaii

Re: 8" plates

Post by OtisT »

I am looking forward to hearing about your results Shady. One specific question will be how much power you will use for a moderate spirit run rate.

I have an 8” ferrule on my boilers and am thinking about putting two or three plates on that before reducing diameter.

Following with interest. Otis
Otis’ Pot and Thumper, Dimroth Condenser: Pot-n-Thumper/Dimroth
Learning to Toast: Toasting Wood
Polishing Spirits with Fruitwood: Fruitwood
Badmotivator’s Barrels: Badmo Barrels
User avatar
Copperhead road
Distiller
Posts: 2090
Joined: Thu Jan 12, 2017 4:28 pm
Location: Brisvegas downunder OZ

Re: 8" plates

Post by Copperhead road »

OtisT wrote: ↑Sat Oct 03, 2026 12:40 pm I am looking forward to hearing about your results Shady. One specific question will be how much power you will use for a moderate spirit run rate.

I have an 8” ferrule on my boilers and am thinking about putting two or three plates on that before reducing diameter.

Following with interest. Otis
i have been waiting for Shady to post an update.
I have been following this thread with interest... Thanx for giving it a bump otis. :ewink:
Never mistake kindness for weakness....
30xs
Rumrunner
Posts: 683
Joined: Thu Jan 03, 2019 6:05 pm
Location: WV

Re: 8" plates

Post by 30xs »

Hanging out with Otis and Copper waiting.
User avatar
shadylane
Master of Distillation
Posts: 12870
Joined: Sat Oct 27, 2007 11:54 pm
Location: Hiding In the Boiler room of the Insane asylum

Re: 8" plates

Post by shadylane »

OtisT wrote: ↑Sat Oct 03, 2026 12:40 pm I am looking forward to hearing about your results Shady. One specific question will be how much power you will use for a moderate spirit run rate.

I have an 8” ferrule on my boilers and am thinking about putting two or three plates on that before reducing diameter.

Following with interest. Otis
I'll start by running wide open just for shits and grins. The elements are supposed to be 4.5kw each @ 240v.
According to my measurements the elements have a higher resistance than they should and including voltage drop I figure just slightly above 4kw.
Just guessing the plates sweet spot will be around 5 - 6kw but only time and experience can decide that.

It's finally cooled off enough to catch up on all the "honey do" things my wife has on her list.
But in the near future, I'll run a sacrificial sugar wash to get some hard numbers for Ya'll.
Post Reply