Red corn bourbon with heirloom rye and malt

Grain bills and instruction for all manner of alcoholic beverages.

Moderator: Site Moderator

Post Reply
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Distillers.

My last project for 2026 is going to be my most ambitious yet. I thought I'd share my plans with you. I want to make a Bourbon with a high rye content, using a mix of raw rye and malted rye. Since I want to stick it into my new 20L/5gbarrel, I am planning to make about 25-27L/7g of product in total. I've never made this much whiskey before in one project. I call it Red Diamond Whiskey.

Having had a bad experience from making high rye Bourbon last year, I am being a bit more moderate with the amount of rye this time. In the long run though, I want this Whiskey to have at least 30% rye but for now I am content with 20% rye. The remaining grains are 68% corn and 12% barley malt.

The Rye
I like the flavors from malt and I think rye malt makes a lovely addition in whiskey. However, during this year my interest for heirloom grains have grown from non-existent to big, and I have decided that the raw rye element of the mash bill should not only be heirloom rye, it should constitute 2/3 of the rye portion.

Being the main flavor ingredient in rye Bourbons, I've researched rye in distilling is a lot. In commercial Bourbons, it seems to be all about raw rye. After researching wheat, realizing how far commercial wheats have come from the original wheats we used just 150 years ago, I have understood the same goes for rye. However, a number of small scale Whiskey producers in the US are trying out older, heirloom, rye varieties. Rosen rye is often mentioned, as is Abruzzi rye, and used by a some craft distillers. However, on this side of the pond neither are available. The good thing is that the interest for heirloom grain is global. In Germany, a big consumer of rye bread and thus a big producer of rye grains, several heirloom rye varieties are making their way back.

In my research I made a friend in German farmer and grain distributor Reimund Wiederhold from WIDU Mühlenbau. His locale is near Rotenburg, 45 minutes south of Hamburg, which is a grain growing region as much as any. One of his heirloom ryes is the Champagne rye, aka Champagneroggen. It has its' origins in the north of France, from the area of Champagne, but I am unsure if it is still grown there. The French affiliation with wheat seems to have forced the Champagne rye to emigrate east. After some deliberations, I decided to go with Champagne rye as my raw rye component in Red Diamond. On my way back from Portugal this summer, I stopped by Reimund at his farm, and picked up 14kg/31lb of his Champagne rye.

Champagne rye is supposedly slightly nutty, milder and sweeter than normal rye. It's considered a bit more refined than normal rye. How it will show up in distilled format is unknown to me.

I will also use rye malt. Two types: pale rye malt and crystal rye malt, equal amounts. Both provide a bit spicy crackers flavor that I particularly like.

The Corn
Calling the Whiskey Red Diamond is not entirely picked out of the blue (pun intended). I've wanted to make a Bourbon using the red corn varieties Bloody Butcher or Jimmy Red, but just as with the US heirloom rye varieties, neither are available in Europe. In Europe, however, several countries are growing more than just yellow dent corn. The Italians love flint corn for their Polenta and one of their highest prized corn varieties is a red heirloom variety called Pignoletto Rosso. It's possible for me to get it as course ground flour but not whole, which is what I want. In Portugal, there's the Milho Rei, another red corn variety, and when I was in Portugal this summer I contacted several grower who say they have Milho Rei but all were out. It's a popular variety and sells out soon after harvest, a lady grower told me.

And in France they grow two red varieties that both are used for pigeons: Bordeaux Cribbs and a variety that is often just called Red Corn, or French Red. Since I have made a friend in Sweden's leading pigeon racing club, I am able to piggy back from his club's shipping from Belgium and buy both types of red corn. I will use both in my Red Diamond.

I have also been able to harvest at least two ears of my own grown Atomic Orange corn, which I will add to the mash bill. We are talking about max 20 kernels, but probably the best corn in Sweden. ;)

The Barley malt
Finally there's the 12% of barley malt. The heirloom focus continues and I will use Chevallier malt from the UK. Chevallier is a old variety that was very popular all over Europe in the 1800's and very popular with brewers because of the strong malty flavor it provides. It fell out of fashion at the turn of the century as brewers fancied Maris Otter and distillers fancied Golden Promise instead. But Simpson's maltster has brought the barley variety back and it has become popular with hobby brewers and hobby distillers alike. I've used it in my Green Diamond recipe and liked it.

The Recipe in short
68% Red Corn
20% Rye (12% Champagne rye, 8% rye malt)
12% Chevallier Barley malt

The process
I will use YLAY for cold mashing and fermentation. For each batch, I will use 13kg/29lb of grains with 45L/12g of water, in a 60L/15.5g barrel. The grains will pre-soak in 25L/6.5g water, starting at 68C/154F, then allowing it to fall in temp over 4-5 hours. The soaked grains are brought to pitching temp by the addition of the remaining 20L/5g water, coming cold from the fridge. Typically, these batches give me a wash after draining and separating gunk of 37L/10g.

I considering if I should soak the rye first in 45C/113F water for a 30 minutes combined beta-glukan and protein rest. I will normally do a beta-glukan rest when mash traditionally and there's rye or oats in the mash bill, however if it's really needed for YLAY mashing I don't know. I am thinking it can't hurt but it may just be a waste of time. I also considering to add enzymes for the beta-glucans. I've got this Polish enzyme that is supposedly good for rye batches. I don't have experience with raw rye so I'm not sure what to expect when it comes to rye goo.

As I want about 25-27L/7g of product to use in the barrel, I will need to split the project up in three spirit runs. Each stripping run will give approximately 12L/3g low wines at 25% ABV.
- 4 stripping runs and 1 spirit run (no feints available)
- 3 stripping runs and 1 spirit run (with feints)
- 2 stripping runs and 1 spirit run (with feints)

This project will keep me busy up to and over xmas.

... and in conclusion
My idea with getting a 20L/5g barrel was to get into fewer projects. Focusing on one or two whiskey projects per year to fill the barrel up, then have time for other things. Then I realized how much work there is to just fill a 20L/5g barrel. Working with 60L/15.5g barrels is fine for shorter projects but when you need to make so much wash one needs to do a lot of batches. I've been contemplating to upgrade to bigger volumes but I am pushing that for the future. So 9 batches it is.

A couple of things concern me:

- Rye is a b*tch sometimes but with malted rye I've been spared the goo and the stickiness. Should I expect much more pain and grief with raw rye? Tell me your best rye story, if you have one?
- YLAY and rye seem to work fine, have anyone actually had rye-related problems with YLAY?
- Scorching. I am running internal elements, be it wavey ULD elements, I am not safe from scorching. I don't have a steam stripping set up and will not have it for this project either. I will be running very carefully the first stripping runs before I feel how fast I dare to run, spreading the heat over both elements.

Still, I am really looking forward to using the raw Champagne rye.
HeyBroChuckNorris
Posts: 117
Joined: Sun Apr 14, 2024 9:58 pm

Re: Red corn bourbon with heirloom rye and malt

Post by HeyBroChuckNorris »

This is an awesome project. Well researched and ambitious. I'd love to try to fill a 20L barrel at some point, but man that is a lot of work on a 35L boiler. Definitely putting something like that in the lofty goals section of my mental notes.
User avatar
Username
Swill Maker
Posts: 423
Joined: Wed Oct 25, 2017 10:15 am

Re: Red corn bourbon with heirloom rye and malt

Post by Username »

Oh man, you don't mess around. This sounds fantastic and a lot of work, even before you put the first mash on. Nice thought process and planning, looking forward to reading the story of this as it progresses
tommysb
Rumrunner
Posts: 562
Joined: Thu Oct 29, 2020 12:09 pm

Re: Red corn bourbon with heirloom rye and malt

Post by tommysb »

Sounds amazing Pal - I imagine this will be next-level good.

You put me onto the Brewmix-Plus enzyme - why not use that in your mashing to reduce gumminess? Not sure how your Yellow Label protocol works, or how it fits in, but I've had no problems with Rye when I use it. I can't see any downsides to using it.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

tommysb wrote: ↑Mon Sep 28, 2026 12:31 am Sounds amazing Pal - I imagine this will be next-level good.

You put me onto the Brewmix-Plus enzyme - why not use that in your mashing to reduce gumminess? Not sure how your Yellow Label protocol works, or how it fits in, but I've had no problems with Rye when I use it. I can't see any downsides to using it.
You dont do beta-glucan rests with rye, relying only on the enzyme, Tom? I didnt actually think about the Brewmix plus, you know my enzyme stash better than I do! :)

With YLAY I heat up 25L of mash water to 72c, put the brewbag in the barrel and fill it with corn crush/meal, and pour the hot mash water on top of it, stirring to not get any dough balls. The hope is it will pasturize the corn. The temp in the barrel falls quite quickly and at 60-62c I add the remaining grains. I use a low temp alpha amylase and seal the bucket up to hold the temp around 58C for 60 minutes. Then I turn off heat belts, remove insulation, and let it cool down naturally. A few hours later, I add the remaining 20 liters of cold water to get the mash to pitching temp.

In theory, it converts most of starches from the small grains before I add YLAY. YLAY will focus on converting the corn and any starches that wasnt converted during the soak.

If I add the brewmix plus, it would have to be at the point I add the small grains. The protease and xylanase works best below 60C. Normally, I add Brewmix at mash-in (at 40C) but here it would be added at cool down. Not sure at what temp Brewmix deteriorates.
tommysb
Rumrunner
Posts: 562
Joined: Thu Oct 29, 2020 12:09 pm

Re: Red corn bourbon with heirloom rye and malt

Post by tommysb »

I've read a couple different things, i think it describes itself as 'high temp'. I use on heat-up, which means it passes through the beta-glucan range.

If it were me, I would throw a bit in at mash in, and just accept that some of the enzyme activity may be reduced through denaturing when temp >60c. Then, when it dropped below 60c, I would throw in a bit more.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

tommysb wrote: ↑Mon Sep 28, 2026 3:04 am I've read a couple different things, i think it describes itself as 'high temp'. I use on heat-up, which means it passes through the beta-glucan range.

If it were me, I would throw a bit in at mash in, and just accept that some of the enzyme activity may be reduced through denaturing when temp >60c. Then, when it dropped below 60c, I would throw in a bit more.
That's a good idea, Tom.
Novice
Swill Maker
Posts: 182
Joined: Fri Aug 22, 2025 2:55 pm

Re: Red corn bourbon with heirloom rye and malt

Post by Novice »

This might give you an idea.
viewtopic.php?t=96325
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Today I mashed in my first batch of Red Diamond Whiskey.

Red Corn: 8.45kg/18.5lb (64%)
Yellow Corn: 0.75kg/1.5lb (6%)
Pale Rye malt: 0.5kg/1.1lb (4%)
Red Rye Crystal malt: 0.5kg/1.1lb (4%)
Champagne Rye (raw): 1.4kg/3lb (10%)
Chevallier Barley malt: 1.6kg/3.5lb (12%)

image.jpg
Here are the grains used. The upper plate to the right is just to show the difference in size between distiller's malt (the upper) and Chevallier malt, the bottom.

image.jpg
Small red Bordeaux Cribbs corn

image.jpg
The rye, from left to right: Red Rye Crystal malt, Pale Rye malt, and Champagne Rye

image.jpg
Chevallier Barley malt.
You do not have the required permissions to view the files attached to this post.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Mashing/Pre-soaking procedure:

Heated 25L/6.6g of mash water to 75C/167F. Added 5ml Endozym Brewmix Plus (enzyme mix), 3.4gr of Epsom salt and 6.7gr Chalk to mashing water during heat up.

Dressed the mash-fermentaion barrel with a 800 micron brewbag, filled it with the corn. Poured 15L/4g of the hot mash water on top of the corn, stirring well. As temp dropped to 61C/142F I added the remaining 10L/2.6g of hot mash water to the mash-fermenter and stirred in the rye and malt. Added another 5ml of Endozym Brewmix Plus to the mash, insulated the barrel, and turned on two heat belts. Let the barrel sit for 1 hour.

After 1 hour I removed the barrel insulation, turned off the heat belts, added 4ml of Glucoamylase, and stirred well. Let the barrel sit to cool down until temp in barrel is 40C/104F. Then I added 19L/5g cold water to land at 31C/89F. Checking the PH, we are good at 5.6.

Hydrating 63gr of YLAY and 22gr of USW-6 in 32C/89F water for 15 minutes, while oxygenating the mash with my drill mounted propeller. After 15 minutes hydration, both yeasts were pitched, and barrel insulated again.
tommysb
Rumrunner
Posts: 562
Joined: Thu Oct 29, 2020 12:09 pm

Re: Red corn bourbon with heirloom rye and malt

Post by tommysb »

How was the rye viscosity/guminess? Did the enzyme help?
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

The mash was thicker, Tom, but totally managable. No problem.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

tommysb wrote: ↑Wed Oct 07, 2026 5:46 pm How was the rye viscosity/guminess? Did the enzyme help?
Now that I am fermenting the mash really feels like any other. I really think YLAY includes enzymes and whatnot thar manages beta-glukans. Never had foaming with YLAY, and no issues up to now with slime.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Racked off and drained the first batch of Red Diamond Whiskey yesterday. I've had two batches with 5 days apart fermenting on YLAY, both have some sort of infection, probably lacto, becuase the PH dropped to 3.2 and the fermentation got sluggish. Used Calcium Hydroxide to up it to 3.5-3.6 to get the fermentation going again.

But man the amount of gunk with this batch! Normally I drain into two buckets. Both usually end up with about 2L/0.5g of gunk after it settles. The first bucket is sitting with 5L gunk, but it hasn't finished settling yet so I am hopeful it will recede further. I also got less wash after draining than I normally get. Maybe a one off? We'll see, but I may have a lower yield than I have calculated with.
tommysb
Rumrunner
Posts: 562
Joined: Thu Oct 29, 2020 12:09 pm

Re: Red corn bourbon with heirloom rye and malt

Post by tommysb »

You are going to have to do a steam boiler eventually!
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

tommysb wrote: ↑Wed Oct 21, 2026 11:30 pm You are going to have to do a steam boiler eventually!
Lol. But first I need to rebuild my distillery.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

First stripping run of my high heirloom rye Bourbon is done. I ran it yesterday. I am still mentally scarred from last year's attempt to make a high rye Bourbon, which ended in a bad scorch. In hindsight, with the help of experience learned myself and experience received from others, I can see a lot of wrongs that led up to the scorch, but I am still troubled by it. As a result I have taken quite a few precautions since to not let it happen again.

Today I run the still with two ULD elements, sharing the wattage equally between the two, and when I stripped yesterday I only ran a total of 2500w over the two elements. It went fine although both yield and ABV from the ferment were disappointing. However, I noticed after the run as I was rinsing the equipment that the lower of my two elements had collected a lot of white "spots". Like fine sand corns. The other element looked normal.

Quite possibly, maybe even quite probably, this is from the unmalted rye and perhaps the corn. After researching it seems most likely to be "beerstone", which is starch. Anyone familiar with beerstone residue?
User avatar
Username
Swill Maker
Posts: 423
Joined: Wed Oct 25, 2017 10:15 am

Re: Red corn bourbon with heirloom rye and malt

Post by Username »

In my experience beerstone tends to cover large area's and builds in very thin layers rather than spots.

I don't know if you're a tea drinker with a favourite mug that doesn't see much washing. The tea stain that builds on the mug is the closest thing to beerstone I've seen in everyday life
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Username wrote: ↑Mon Oct 26, 2026 12:34 am In my experience beerstone tends to cover large area's and builds in very thin layers rather than spots.

I don't know if you're a tea drinker with a favourite mug that doesn't see much washing. The tea stain that builds on the mug is the closest thing to beerstone I've seen in everyday life
Ok, thanks username. What you're suggesting is the kind of dark coating my elements have normally gathered over the last year or so. So what the heck were those spots? I cleaned the elements in PBW this morning and both now looks almost like new. It will be interesting to see if I have new "spots" after the next stripping run.
User avatar
Username
Swill Maker
Posts: 423
Joined: Wed Oct 25, 2017 10:15 am

Re: Red corn bourbon with heirloom rye and malt

Post by Username »

PalCabral wrote: ↑Mon Oct 26, 2026 2:13 am What you're suggesting is the kind of dark coating my elements have normally gathered over the last year or so.
Exactly Pal, that coating that builds up over time is beerstone, if left too long it becomes very difficult to remove.

Every now and then I'll remove the elements and soak the business end in hot oxi-clean, it does a fantastic job
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Oxi Clean is a stain remover, I had to google it. I guess it makes sense.
User avatar
Username
Swill Maker
Posts: 423
Joined: Wed Oct 25, 2017 10:15 am

Re: Red corn bourbon with heirloom rye and malt

Post by Username »

PalCabral wrote: ↑Mon Oct 26, 2026 3:52 am Oxi Clean is a stain remover, I had to google it. I guess it makes sense.
I use supermarket own brands, it's a sodium percarbonate cleaner, actually very similar to pbw when I look at it :lol:
tommysb
Rumrunner
Posts: 562
Joined: Thu Oct 29, 2020 12:09 pm

Re: Red corn bourbon with heirloom rye and malt

Post by tommysb »

Yeah, drop in laundry cleaner with 'oxy' in the title. As Username says, it's Sodium Percarbonate. Vanish would be a name brand one, here's what i use:
image.png
You do not have the required permissions to view the files attached to this post.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Today I am mashing my third batch of Red Diamond Whiskey. This time I am using a new corn variety, French Red. Looking forward to try it out. It’s a bit lighter in color and bigger in size than the Bordeaux Cribbs I used in the first two batches.
IMG_8951.jpeg
You do not have the required permissions to view the files attached to this post.
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Tomorrow I am going to have my first of three spirit runs of the Red Diamond high rye Bourbon. After the first four batches, I can say that the yield using rye is considerably lower than for my normal Bourbon batches, high in wheat or barley. The grains absorbs more liquid and the gunk factor is bigger. The mash is also a lot more viscous which means that it needs more time to settle, and careful racking and slower stripping.

Not all of it is down to the rye though. The red corn is lower in extract and is consistently giving me lower alcohol yield than when I run with yellow corn. It's a bad combo, lower extract and more grain absorbtion. 4 batches would typically have given me 48L/12.5g low wines at 25-26%, now I have 40L/10.5g low wines at 24% instead. Well well, let's hope the whiskey flavor makes up for it. ;)
Beerswimmer
Trainee
Posts: 976
Joined: Tue Sep 29, 2009 1:33 pm
Location: In the garage

Re: Red corn bourbon with heirloom rye and malt

Post by Beerswimmer »

Big day, I hope it goes smoothly! Curious about the flavors you get!
Ut Alii Vivant!!!!
User avatar
PalCabral
Posts: 2797
Joined: Tue Oct 29, 2024 4:02 am
Location: Stockholm, Sweden

Re: Red corn bourbon with heirloom rye and malt

Post by PalCabral »

Beerswimmer wrote: ↑Sun Nov 22, 2026 12:32 am Big day, I hope it goes smoothly! Curious about the flavors you get!
Early times yet, on the second jar only, but my the fruity flavors I'm getting from the heads are lovely. But I am probably jinxing it now - the flavor is horrible :wink:
Post Reply