Valve: Difference between revisions
Jump to navigation
Jump to search
(new, started, saving work.) |
(Finishing first round) |
||
| Line 3: | Line 3: | ||
=Characteristics= | =Characteristics= | ||
In distilling there are four main attributes we look at when comparing valves: | In distilling there are four main attributes we look at when comparing valves: | ||
:Start/ | :'''Start/stop:''' This is the amount of time it takes to turn fully on to fully off (and visa versus). When deciding why type of valve to use you should understand if you need to turn it on or off in a hurry. | ||
:Absolute | :'''Absolute Volume:'''Relative to the diameter of the pipe, how much does this valve restrict the flow of water when fully open. | ||
:Flow Control: How precisely will controlling the flow matter? | :'''Flow Control:''' How precisely will controlling the flow matter? | ||
: | :'''Solids:''' Can this handle solids or should it be used for pure liquids only. | ||
=Major types= | =Major types= | ||
===Ball Valve=== | ===Ball Valve=== | ||
A ball valve is the most common type of valve that is used in distilling due to its low cost. It best used is in situations where the valve will be used fully open or closed like moving water or mash from one container or another. Ball valves offer inconsistent flow rates even when moved to the same position. | A ball valve is the most common type of valve that is used in distilling due to its low cost. It best used is in situations where the valve will be used fully open or closed like moving water or mash from one container or another. Ball valves offer inconsistent flow rates even when moved to the same position. Used for smaller diameter openings up to 2". | ||
:Start/stop: It is very easy to turn fully on to fully off. | :'''Start/stop:''' It is very easy to turn fully on to fully off. | ||
:Absolute Volume: Ball valves allow full flow of water for a given diameter of pipe. | :'''Absolute Volume:''' Ball valves allow full flow of water for a given diameter of pipe. | ||
:Flow Control: Flow control is difficult with a ball valve. | :'''Flow Control:''' Flow control is difficult with a ball valve. | ||
:'''Solids:''' It is able to pass solids like mash. At diameters less than 1" it may be difficult. | |||
===Gate Valve=== | ===Gate Valve=== | ||
A gate valve is less common. It offers some control over flow while still allowing full volume of fluid to pass. This valve is useful for situations that requires some control but not fine control. Control to a condenser would be a good use. | A gate valve is less common. It offers some control over flow while still allowing full volume of fluid to pass. This valve is useful for situations that requires some control but not fine control. Control to a condenser would be a good use. | ||
:Start/stop: It is slower to turn fully on to fully off than a ball valve. | :'''Start/stop:''' It is slower to turn fully on to fully off than a ball valve. | ||
:Absolute Volume: Gates valves allow full flow of water for a given diameter of pipe. | :'''Absolute Volume:''' Gates valves allow full flow of water for a given diameter of pipe. | ||
:Flow Control: Flow control fairly easy but not precise. | :'''Flow Control:''' Flow control fairly easy but not precise. | ||
:'''Solids:''' Not recommended for solids. | |||
===Needle Valve=== | ===Needle Valve=== | ||
Needle valves are used where precise flow control is needed. Needle valves are common in [https://homedistiller.org/forum/viewtopic.php?f=1&t=46605 Liquid Management | Needle valves are used where precise flow control is needed. Needle valves are common in [https://homedistiller.org/forum/viewtopic.php?f=1&t=46605 Liquid Management] type stills. | ||
:Start/stop: It is very slow to fully turn on and off. | :'''Start/stop:''' It is very slow to fully turn on and off. | ||
:Absolute Volume: Needle valves reduce the available volume to pass. | :'''Absolute Volume:''' Needle valves reduce the available volume to pass. | ||
:Flow Control: Flow control is easy and precise. | :'''Flow Control:''' Flow control is easy and precise. | ||
:'''Solids:''' Do not used with solids. | |||
===Butterfly Valve=== | ===Butterfly Valve=== | ||
The closing mechanism is a disk that rotates. Ok for solids like mash. Commonly used for larger diameters from 1" on up. | |||
:'''Start/stop:''' It is easy to fully turn on and off. | |||
:Start/stop: It is easy to fully turn on and off. | :'''Absolute Volume:''' Allows full volume for diameter of pipe. | ||
:Absolute Volume: Allows full volume for diameter of pipe. | :'''Flow Control:''' Flow control difficult. | ||
:Flow Control: Flow control difficult. | :'''Solids:''' It is able to pass solids like mash. At diameters less than 1" it may be difficult. | ||
===Relief Valve=== | ===Relief Valve=== | ||
A relief valve or pressure relief valve (PRV) is a type of safety valve used to control or limit the pressure in a system; pressure might otherwise build up and create a process upset, instrument or equipment failure, or fire. The pressure is relieved by allowing the pressurized fluid to flow from an auxiliary passage out of the system. In distilling we use pressure and vacuum relief valves. Both are normally set to a fixed PSI before they open, depending if they are used for the main boil kettle (5 psi)or in a steam jacket (15 psi or 1 bar). | |||
:Start/stop: Relief valves are set to a specific pressure. They remain closed until that pressure level is reached. | |||
:Absolute Volume: Not applicable, this is a safety item. | |||
:Flow Control: Not applicable, this is a safety item. | |||
=External Links= | =External Links= | ||
*[https://en.wikipedia.org/wiki/Valve Valve on Wikipedia] | *[https://en.wikipedia.org/wiki/Valve Valve on Wikipedia] | ||
*[https://megadepot.com/resource/a-guide-to-types-of-valves Types of Valves] | *[https://megadepot.com/resource/a-guide-to-types-of-valves Types of Valves] | ||
*[https://en.wikipedia.org/wiki/Ball_valve Ball Valve on Wikipedia] | |||
*[https://en.wikipedia.org/wiki/Gate_valve Gate Valve on Wikipedia] | |||
*[https://en.wikipedia.org/wiki/Needle_valve Needle Valve on Wikipedia] | |||
*[https://en.wikipedia.org/wiki/Butterfly_valve Butterfly valve on Wikipedia] | |||
*[https://en.wikipedia.org/wiki/Relief_valve Relief Valve on Wikipedia] | |||
Revision as of 10:12, 6 February 2019
A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways.
Characteristics
In distilling there are four main attributes we look at when comparing valves:
- Start/stop: This is the amount of time it takes to turn fully on to fully off (and visa versus). When deciding why type of valve to use you should understand if you need to turn it on or off in a hurry.
- Absolute Volume:Relative to the diameter of the pipe, how much does this valve restrict the flow of water when fully open.
- Flow Control: How precisely will controlling the flow matter?
- Solids: Can this handle solids or should it be used for pure liquids only.
Major types
Ball Valve
A ball valve is the most common type of valve that is used in distilling due to its low cost. It best used is in situations where the valve will be used fully open or closed like moving water or mash from one container or another. Ball valves offer inconsistent flow rates even when moved to the same position. Used for smaller diameter openings up to 2".
- Start/stop: It is very easy to turn fully on to fully off.
- Absolute Volume: Ball valves allow full flow of water for a given diameter of pipe.
- Flow Control: Flow control is difficult with a ball valve.
- Solids: It is able to pass solids like mash. At diameters less than 1" it may be difficult.
Gate Valve
A gate valve is less common. It offers some control over flow while still allowing full volume of fluid to pass. This valve is useful for situations that requires some control but not fine control. Control to a condenser would be a good use.
- Start/stop: It is slower to turn fully on to fully off than a ball valve.
- Absolute Volume: Gates valves allow full flow of water for a given diameter of pipe.
- Flow Control: Flow control fairly easy but not precise.
- Solids: Not recommended for solids.
Needle Valve
Needle valves are used where precise flow control is needed. Needle valves are common in Liquid Management type stills.
- Start/stop: It is very slow to fully turn on and off.
- Absolute Volume: Needle valves reduce the available volume to pass.
- Flow Control: Flow control is easy and precise.
- Solids: Do not used with solids.
Butterfly Valve
The closing mechanism is a disk that rotates. Ok for solids like mash. Commonly used for larger diameters from 1" on up.
- Start/stop: It is easy to fully turn on and off.
- Absolute Volume: Allows full volume for diameter of pipe.
- Flow Control: Flow control difficult.
- Solids: It is able to pass solids like mash. At diameters less than 1" it may be difficult.
Relief Valve
A relief valve or pressure relief valve (PRV) is a type of safety valve used to control or limit the pressure in a system; pressure might otherwise build up and create a process upset, instrument or equipment failure, or fire. The pressure is relieved by allowing the pressurized fluid to flow from an auxiliary passage out of the system. In distilling we use pressure and vacuum relief valves. Both are normally set to a fixed PSI before they open, depending if they are used for the main boil kettle (5 psi)or in a steam jacket (15 psi or 1 bar).
- Start/stop: Relief valves are set to a specific pressure. They remain closed until that pressure level is reached.
- Absolute Volume: Not applicable, this is a safety item.
- Flow Control: Not applicable, this is a safety item.