Valved Reflux Still
Moderator: Site Moderator
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Valved Reflux Still
Im currently building a valved reflux still. I have all the directions and im sure everyone is familiar with the specs. I just want to know if I need a 3"cap for the top of the condenser shell. I have tried looking at pictures and reading through directions, but I haven't seen or read anything about a covering for the condenser shell. I would immaging that it would need one and feel dumb asking this question, but better safe than sorry right?
http://www.moonshine-still.com/Photo/Ex ... denser.jpg" onclick="window.open(this.href);return false;" rel="nofollow
http://www.moonshine-still.com/Photo/Ex ... denser.jpg" onclick="window.open(this.href);return false;" rel="nofollow
- LWTCS
- Site Mod
- Posts: 13301
- Joined: Mon Jan 26, 2009 6:04 pm
- Location: Treasure Coast
Re: Valved Reflux Still
Cap with a vent hole so your (forthcoming) rig remains open to the atmosphere.
Trample the injured and hurdle the dead.
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
Im confused, how big of a hole? is it more like a pressure release valve on a pressure cooker? Do you have any pictures?
- LWTCS
- Site Mod
- Posts: 13301
- Joined: Mon Jan 26, 2009 6:04 pm
- Location: Treasure Coast
Re: Valved Reflux Still
21/64ths will work.
Don't want to build pressure while your take off valve is closed.
Not a pressure release as such. The condenser, if in good working order will knock down all of the vapor, thus preventing vapor escape and the hole allows for preventing pressure build up.
Don't want to build pressure while your take off valve is closed.
Not a pressure release as such. The condenser, if in good working order will knock down all of the vapor, thus preventing vapor escape and the hole allows for preventing pressure build up.
Trample the injured and hurdle the dead.
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
ok, that makes sense now. thanks.
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
honestly, if you can, dont buy the cap or take it back. If I remember, i paid about $35 for a 3" copper cap. You dont need it, although, if yer condenser isnt that efficient, you do need something there to slow down the vapor. I used a couple copper scrubbers. alot cheaper. just my .02
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
I just bought the cap yesterday online. at least it will look nice. Also, I don't know how efficient my condenser will be. Im planning on getting started on building the still tomorrow. I'll keep you guys posted.
-
still crazy
- Rumrunner
- Posts: 706
- Joined: Wed Feb 03, 2010 6:11 am
Re: Valved Reflux Still
LWTCS wrote:21/64ths will work.![]()
EVIL but I laughed !!
Daddy used, to say " Any landing you can walk away from is a good one"
Calculations don't mean shit when compared to the real world practical experience of many...RAD 9/2010
Calculations don't mean shit when compared to the real world practical experience of many...RAD 9/2010
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
If im guessing right, your building a mirror image of my first still. Let me help you learn from my mistakes. I wouldnt build the condenser into the side of the collumn like they say, too hard to clean. I would wrap a nice condenser like the relflux condenser in the boka bobs seen on the site. incorporate that into your cap with the feed and discharge lines sticking out of the cap. drill an extra hole or two in the cap. Then you have a removeable condenser. much better. plus you should be able to build it longer and therefore more efficient. I didnt think of that until after I had mine built...... hind sight is 20/20.
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
Fastill
- Trainee
- Posts: 898
- Joined: Sat Mar 13, 2010 6:28 pm
- Location: Where we drink more beer than you!
Re: Valved Reflux Still
I run an offset head and use no cap at all. I just drop the condenser coil in and fire her up. No vapor comes out if everything is set correctly, ( coolant flow, heat input,).
A.D.D. and HD don't go together. This hobby takes time and dedication to learn and do it right and safe.
Fill the pool before you jump in head first!
http://homedistiller.org/forum/viewtopi ... 15&t=52975
Fill the pool before you jump in head first!
http://homedistiller.org/forum/viewtopi ... 15&t=52975
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
I have already bought all the parts so im gonna stick with the original plan, but im going to leave the cap on the condenser un-sodered so that it can be removed and hopefully make it easier to be cleaned.MuleKicker wrote:If im guessing right, your building a mirror image of my first still. Let me help you learn from my mistakes. I wouldnt build the condenser into the side of the collumn like they say, too hard to clean. I would wrap a nice condenser like the relflux condenser in the boka bobs seen on the site. incorporate that into your cap with the feed and discharge lines sticking out of the cap. drill an extra hole or two in the cap. Then you have a removeable condenser. much better. plus you should be able to build it longer and therefore more efficient. I didnt think of that until after I had mine built...... hind sight is 20/20.
-
junkyard dawg
- Master of Distillation
- Posts: 3092
- Joined: Fri Feb 03, 2006 11:40 am
- Location: Texas
Re: Valved Reflux Still
keep your mind open when it comes to building that valved reflux... there are lots of good mods and improvements to the design that have been worked out over the years... some would say there are many better designs out there, but thats a different conversation.
first, you don't need 3" tubing for that condensor, 2" works fine. It should not be built with a cap on the condensor. The coil should be built so that it is easily removed.
That arm that connects the condensor to the main column is going to fill with gunk when you run. It is important to have access to clean that. I used a 1/2" threaded connector inline with the arm. A dial thermometer sits there until it needs cleaning.
Those wacky schemes to attach it to the keg are just dumb. I welded a 2" half coupling to the top of the keg and a 2" npt male fitting on the column and have a gasket-less totally secure connection.
There are also thoughts about only using one valve... its all you really need anyway.
Good luck with your build...
first, you don't need 3" tubing for that condensor, 2" works fine. It should not be built with a cap on the condensor. The coil should be built so that it is easily removed.
That arm that connects the condensor to the main column is going to fill with gunk when you run. It is important to have access to clean that. I used a 1/2" threaded connector inline with the arm. A dial thermometer sits there until it needs cleaning.
Those wacky schemes to attach it to the keg are just dumb. I welded a 2" half coupling to the top of the keg and a 2" npt male fitting on the column and have a gasket-less totally secure connection.
There are also thoughts about only using one valve... its all you really need anyway.
Good luck with your build...
this is the internet
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
could you post up any pics of that part? ^junkyard dawg wrote:keep your mind open when it comes to building that valved reflux... there are lots of good mods and improvements to the design that have been worked out over the years... some would say there are many better designs out there, but thats a different conversation.
first, you don't need 3" tubing for that condensor, 2" works fine. It should not be built with a cap on the condensor. The coil should be built so that it is easily removed.
That arm that connects the condensor to the main column is going to fill with gunk when you run. It is important to have access to clean that. I used a 1/2" threaded connector inline with the arm. A dial thermometer sits there until it needs cleaning.
Those wacky schemes to attach it to the keg are just dumb. I welded a 2" half coupling to the top of the keg and a 2" npt male fitting on the column and have a gasket-less totally secure connection.
There are also thoughts about only using one valve... its all you really need anyway.
Good luck with your build...
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
junkyard dawg wrote:That arm that connects the condensor to the main column is going to fill with gunk when you run.
I have never had that happen. Maybe if your distilling on the grain or something?
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
junkyard dawg
- Master of Distillation
- Posts: 3092
- Joined: Fri Feb 03, 2006 11:40 am
- Location: Texas
Re: Valved Reflux Still
Mulekicker, I used to run a double boiler rig. I'd do stripping runs with everything in the boiler...
this is the internet
-
Samohon
- retired
- Posts: 3432
- Joined: Mon Oct 05, 2009 4:22 am
- Location: Somewhere in the UK...
Re: Valved Reflux Still
I use a cap with a 3/4 hole for the atmosphere outlet. Don't really need it, but it gives my coil a solid fixing into the head
and makes sure it is centralised. It's not soldered, no PTFE tape or anything. It just sits there... regards....

and makes sure it is centralised. It's not soldered, no PTFE tape or anything. It just sits there... regards....
You do not have the required permissions to view the files attached to this post.
♦♦ Samohon ♦♦
Beginners should visit The New Distillers Reading Lounge and the Safety and Related Issues among others...
Beginners should visit The New Distillers Reading Lounge and the Safety and Related Issues among others...
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
What is the best way to attach the top end to the keg? In the instructions it says to bolt a stainless bowl, but the bowl I have is very thin and I don't think it will work well with all that weight on it. Any advice would be great.
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
have you molested your keg yet? if not, there is a post on making an easy flange by peening out the end of yer collumn. I bought a 2" stainless ferrule and pressed it into the end of my 2" collumn. triclamp it right to the keg with the valve removed.
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
Samohon wrote:I use a cap with a 3/4 hole for the atmosphere outlet. Don't really need it, but it gives my coil a solid fixing into the head
and makes sure it is centralised. It's not soldered, no PTFE tape or anything. It just sits there... regards....![]()
![]()
thats what im talking about samohon. Use the cap as a fixture to hold the coil. Good work my man.
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
I haven't cut up the keg yet. that sounds like a better option. could someone post the link to that topic?MuleKicker wrote:have you molested your keg yet? if not, there is a post on making an easy flange by peening out the end of yer collumn. I bought a 2" stainless ferrule and pressed it into the end of my 2" collumn. triclamp it right to the keg with the valve removed.
-
WalkingWolf
- Angel's Share

- Posts: 1850
- Joined: Fri Nov 20, 2009 6:04 pm
- Location: LA
Re: Valved Reflux Still
easy flange
I use a number 6 wire. I solder on and use as is. No need to "shape"
I find the #4 requires too much "shaping"
I use a number 6 wire. I solder on and use as is. No need to "shape"
I find the #4 requires too much "shaping"
A little spoon feeding for New and Novice Distillers (by Cranky)
Advice- For newbies, by a newbie
Advice- For newbies, by a newbie
Novice Guide for Cuts (pot still)kook04 wrote: maybe cuts are the biggest learning curve, here.
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
thanks, that helps alot. Im definately going to do that instead of the bowl. the only real downside is that its harder to clean, but it looks like its worth it.
- LWTCS
- Site Mod
- Posts: 13301
- Joined: Mon Jan 26, 2009 6:04 pm
- Location: Treasure Coast
Re: Valved Reflux Still
Naw. A well cleared wash and a rinse out when your done will keep you in good working order.cadillac_pimpz wrote:the only real downside is that its harder to clean,
Trample the injured and hurdle the dead.
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
And it will be harder to get the mash inside the keg, but don't get me wrong, it will be much easier than cutting a big hole in the keg and trying to put a stupid bowl on it.LWTCS wrote:Naw. A well cleared wash and a rinse out when your done will keep you in good working order.cadillac_pimpz wrote:the only real downside is that its harder to clean,
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
Heres all the parts I have so far.

keg sitting in my dorm room.


keg sitting in my dorm room.

-
Samohon
- retired
- Posts: 3432
- Joined: Mon Oct 05, 2009 4:22 am
- Location: Somewhere in the UK...
Re: Valved Reflux Still
Lookin good CP, love that copper man...
Keep us posted...
Keep us posted...
♦♦ Samohon ♦♦
Beginners should visit The New Distillers Reading Lounge and the Safety and Related Issues among others...
Beginners should visit The New Distillers Reading Lounge and the Safety and Related Issues among others...
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
your going to need to wrap alot of condenser coil into that head to get any kind of efficiency out of it. that is a spot on match to my first. I would honestly wrap an external coil and incorporate it into that cap. you may find that 3" head piece too short. overall, its a good design, you will like it. the dual valve takes alittle getting used to.
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
Thats the next order of business. theres a total of 6" of the 3" pipe. in the pic, the cap and reducer are pushed all the way in. I can soder the reducer lower without putting stress on it right? I may or may not end up using the cap. I don't want to go with the original plan of this design, instead I want to coil the 1/4" around a 1" pipe, then coil it back, over the 1" coil, with a 2" pipe. It will be difficult to do without crimping the pipe, but the cooling coil will all be made from 1 piece and both connections will go out the top of the 3". The garden hose will be connected there at the top. Do you think that will work?MuleKicker wrote:your going to need to wrap alot of condenser coil into that head to get any kind of efficiency out of it. that is a spot on match to my first. I would honestly wrap an external coil and incorporate it into that cap. you may find that 3" head piece too short. overall, its a good design, you will like it. the dual valve takes alittle getting used to.
-
MuleKicker
- retired
- Posts: 3110
- Joined: Sun Jun 14, 2009 2:14 pm
- Location: If I told you, I'd have to Kill You.
Re: Valved Reflux Still
cadillac_pimpz wrote: I don't want to go with the original plan of this design, instead I want to coil the 1/4" around a 1" pipe, then coil it back, over the 1" coil, with a 2" pipe. It will be difficult to do without crimping the pipe, but the cooling coil will all be made from 1 piece and both connections will go out the top of the 3". The garden hose will be connected there at the top. Do you think that will work?
Yes, that is exactly what i was trying to say. when the coil is dropped in from the top, it can be easily removed for cleaning. you may want to use the cap to hold the coil, just drill a few small holes in it.
-Control Freak-
AKA MulekickerHDbrownNose
AKA MulekickerHDbrownNose
-
cadillac_pimpz
- Novice
- Posts: 35
- Joined: Wed Jun 02, 2010 10:58 am
Re: Valved Reflux Still
any advice for bending the coil? I have a feeling that it will be very difficult to do the way that I want to bend it.