NM
edit here is a template I added to Harry's original design should be to scale if printed with windows picture and fax viewer
![Image](http://i153.photobucket.com/albums/s239/johnhoe/03_partslist.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/04_parts1.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/05_parts3.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/06_parts2.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/07_caps.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/08_caps1.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/09_caps2.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/10_caps3.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/11_Tee.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/12_Tee1.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/13_Tee2.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/14_Tee3.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/15_Tee4.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/16_Tee5.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/17_Tee6.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/18_Tee7.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/19_Tee8.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/20_Tee9.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/21_2Tees10.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/22_Tees-Gate.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/23_compoundmod.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/24_compoundmodvalve.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/25_compoundmodplates.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/26_compoundmodhead.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/29_liebig.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/30_liebig.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/31_liebig.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/32_elbow1.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/32_liebig.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/33_elbow.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/34_liebig1.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/35_liebigcomplete.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/head.jpg)
![Image](http://i153.photobucket.com/albums/s239/johnhoe/case.jpg)
Moderator: Site Moderator
Postby Hawke » Wed Aug 12, 2009 12:49 am
Very nice work.
I see you added the slant plates for foreshot removal.
ImaDKrook wrote:new_moonshiner wrote:With the gate valve in the closed position the slanted plates work just as a LM rig would with everything being taken off from the smaller (brass Valve) This I understand.
The procedure in operating the rig is to use the LM (liquid management ) operation to remove the foreshots and heads which is collected from the smaller brass valve .. once they are removed , then you can close the valve and switch to the Vapor management side using the SS Gate valve Here is my point of confusion. There is no slant plate here.You are taking off Vapor? Then Condensing with Liebig.
To remove to hearts which should not have any contamination from the fores and heads . the rig is still sending liquid down the packing during this time ( it overflows on the bottom plate because the valve is closed) Understand this also and you open the gate to remove a percentage of the vapor which is condensed in the second (liebig) condenser .. Here is the Product/heart cut as a vapor condensed in the Liebig Then onto a jug. I was thinking you were taking off a liquid and was as confused as could be.
Sorry to beat it to death but I wanted to be sure I understood completely.